Officially lowered.....

[seth98esT]

I have an idea, we can probably raise it a little bit from the fork.

You can gan .5-1" if you raise the strut up where it bolts to the strut fork. Just have to be sure you tighten that bolt down very well or else it will just slide down and lower itself.

[4g63lover]

You can gan .5-1" if you raise the strut up where it bolts to the strut fork. Just have to be sure you tighten that bolt down very well or else it will just slide down and lower itself.

yeah thats what I'm planning.

I think I actually rounded the bolt that hold the top mount on the drivers side, any techniques to get it off if we end up actually having to put the stock springs back on?

[EATsleepJDM]

yea i checked the bolt, its pretty rounded.hopefully it will be easy to get it off.

yea does anyone know any ways to get it off when the bolt is rounded?

o and by the way,Jigz do you have a compressor?because i have a impact gun.

[seth98esT]

http://www.sears.com/shc/s/p_10153_12605_00952165000P

You will need a new bolt afterwards.

[4g63lover]

yea i checked the bolt, its pretty rounded.hopefully it will be easy to get it off.

yea does anyone know any ways to get it off when the bolt is rounded?

o and by the way,Jigz do you have a compressor?because i have a impact gun.

bring that impact gun brother!!! I have a 150 psi compressor, hopefully its enough. lol. will make shit go faster. trick coming?

[EATsleepJDM]

thanks a lot seth.i dont mind spending that much for something i can use later on.

so Jigz,do you have a sears near you house just in case??

o nah, my bro isnt coming since he was work form 12pm to 9pm i think.so hope fully we can get it done without his muscles....o yea i think im missing a piece for the impact gun so we may have to buy the piece if we decide to use it.

[4g63lover]

thanks a lot seth.i dont mind spending that much for something i can use later on.

so Jigz,do you have a sears near you house just in case??

yup. hopefully we can keep your springs on cuz it would be a shame if you couldnt use it especially since the car looks baller lowered.

[EATsleepJDM]

yup. hopefully we can keep your springs on cuz it would be a shame if you couldnt use it especially since the car looks baller lowered.

yea i know,its so SICK. and do you have like asuper strong knife or scissor so i can shave a good amount of it because i really like having those mudflaps on, because there is only a half fist clearance from the end of the mudflaps to the ground.

[4g63lover]

yea i know,its so SICK. and do you have like asuper strong knife or scissor so i can shave a good amount of it because i really like having those mudflaps on, because there is only a half fist clearance from the end of the mudflaps to the ground.

shave the mudflap? I got a dremel we can try that
lol

[EATsleepJDM]

lol cool.i know it sounds weird but its a must if i wanna keep them on.

[4g63lover]

lol cool.i know it sounds weird but its a must if i wanna keep them on.

yeah I know what you mean. you dont want to rip it off. lol

[SkylineG1]

Looks good. I think it will be ok when you do the back. The angle of the rake will decrease once the rear come down.

[EATsleepJDM]

thanks man. yea thats what Jigz said also about the angle.

[EATsleepJDM]

sadly i put the stock springs back on.....:(


butttt,the shop that i ordered the lowering springs from,will get the correct springs for my car (since they ordered the 99-04 springs) and when Spring comes around i will put the lowering springs back on again....


YES

[Mike_Rom]

Awww man! that sucks you had to put the stock springs back on!!! Oh well.. next spring it will look HOT