Log in
Register
Reply With QuoteIIRC = If I Recall CorrectlyOriginally Posted by Galant Lopez
The parts guy should know better, it's the same part #'s for the 8G and Eclipse 3G. lol
"IIRC"? Idk wat that means sry, and i thought so. I ordered them from autopartswarehouse and the guy i talked to told me that they wouldnt fit but i read on here that they did...so i went ahead and ordered them anyways.
Sent from my HTC EVO 3D
IIRC = If I Recall Correctly
The parts guy should know better, it's the same part #'s for the 8G and Eclipse 3G. lol
-Chris-
2003 Mitsubishi Galant ES 2.4L SOHC: "Octavia"
2005 Honda Accord EX-L Coupe 2.4L DOHC
Oh haha ya i knew that n well he didnt which had me second thinkin it.
Sent from my HTC EVO 3D
Okay so i finally got a few parts after two weeks of strugglin wit my bank and the stupid website.
im still missin the other front strut, i hope it comes tomorrow cuz i dont want to call them again with another problem. Just ordered the lowerin springs, megan cat-back, and dc strut brace today so an other week of anticipation. Quick question tho, should i get pillow ballmounts?
took the bumper off to primer it but then it was too windy so i just sanded it down and its hangin out in my garage until i get the chance to finish it and get a clear coat on.
Got the cold air intake put in. Would have it further but a slight set bak from andys auto sport had risen, so its gonna b a couple more weeks untill i get anythin else done
Sent from my HTC EVO 3D
you could invest in a can of engine degreaser or some dawn a spray bottle and brush
Haha guess it is pretty bad but i dont have much to show off yet, but good idea i should do that this weekend
Sent from my HTC EVO 3D
http://www.andysautosport.com/mitsub...kits/progress/
http://www.andysautosport.com/mitsub...mounts/ksport/
Im not goin to buy from this website but i use it to get ideas, r these any good?
So got the megan catback the other day and i tried to put it on today but ran into a problem, the flange from the cat pretty much welded the bolts on so i cant get it out. I called a local exhaust shop and hopefully theyll get it on today.
Now since the megan didnt have anywhere to put the o2 sensor on there i just zip tied it for now but my check engine light is on. Any suggestions?
Sent from my HTC EVO 3D
The downstream O2 sensor sets off the P0420 code, you'll need a tune to eliminate the code entirely, or have an exhaust shop tap a new flange for the O2 sensor.
-Chris-
2003 Mitsubishi Galant ES 2.4L SOHC: "Octavia"
2005 Honda Accord EX-L Coupe 2.4L DOHC
its pretty loud with an open cat
Good to know. Is it possible to slice that sensor into the other one that runs right before the cat?
No, they monitor two separate things. The upstream O2 sensor helps regulate the spark and fuel going into the engine. The downstream just monitors the cat.
-Chris-
2003 Mitsubishi Galant ES 2.4L SOHC: "Octavia"
2005 Honda Accord EX-L Coupe 2.4L DOHC
Alright well i think ill just delete the error with a scanner cuz i think this guy will charge me alot more than i want to tap into the megan.
oh ya i almost forgot i got these in today. Im goin to buy new boots and mounts n junk so i can just assemble the struts before i intall them and just pull the old ones out.
The code will come right back after a few miles since you clipped the wire. lol
-Chris-
2003 Mitsubishi Galant ES 2.4L SOHC: "Octavia"
2005 Honda Accord EX-L Coupe 2.4L DOHC
so then the only thin to do is take the bulb out in my cluster? haha
Heres another clip of the exhaust i took off the silencer but its too loud so i put it bak on afterwards
Sent from my HTC EVO 3D
Now i changed my oil a couple days ago and now i hear a tickin in the engine. Idk wat it is, i was able to hear it b4 but now its louder. Im thinkin i have a misfire but not too sure
Sent from my HTC EVO 3D
Posting Rules
Bookmarks