What did u use that step bit for??
Installed oil feed fitting.
Workin on makin a tilt flange for evo manifold. Will post pictures once is fitted and know tht works. Then will finish welding and then coating. As of now is just tacked
Sent from my SM-N920T using Tapatalk
What did u use that step bit for??
'00 Mitsubishi Galant ES 4g64T (Samantha)
'01 Mitsubishi Galant ES 4g64 (Daily)
'02 Mitsubishi Galant ES 4g64 (SCRAPPED)
'00 Mitsubishi Galant ES 4g64 (SCRAPPED)
'91 Volvo 740 Turbo B230FT (SOLD)
'88 Mitsubishi Mighty Max (SOLD)
'91 Kawasaki ZX7 (SOLD)
'95 Kawasaki ZX9R
For the crush copper washers. And same size bit for bandrel fitting.
Sent from my SM-N920T using Tapatalk
Last edited by boosting90; 02-26-2016 at 08:16 PM
Banjo* fitting. Make sure there are no burrs on those washers to insure proper seal.
'00 Mitsubishi Galant ES 4g64T (Samantha)
'01 Mitsubishi Galant ES 4g64 (Daily)
'02 Mitsubishi Galant ES 4g64 (SCRAPPED)
'00 Mitsubishi Galant ES 4g64 (SCRAPPED)
'91 Volvo 740 Turbo B230FT (SOLD)
'88 Mitsubishi Mighty Max (SOLD)
'91 Kawasaki ZX7 (SOLD)
'95 Kawasaki ZX9R
Test fit flange and fits. Tight but fits. Will finish weld this week at work.
Did some wiring done. Did the timing area wires. (Crank,p/s,ac) and wipers plugs was re route same.
Sent from my SM-N920T using Tapatalk
Angle flange is all welded. Next few days with grind smooth. And ceramic coated.
#HomeMade
Sent from my SM-N920T using Tapatalk
Last edited by boosting90; 03-01-2016 at 08:33 PM
Hopefully that flange didn't warp from the heat and will seal properly.
'00 Mitsubishi Galant ES 4g64T (Samantha)
'01 Mitsubishi Galant ES 4g64 (Daily)
'02 Mitsubishi Galant ES 4g64 (SCRAPPED)
'00 Mitsubishi Galant ES 4g64 (SCRAPPED)
'91 Volvo 740 Turbo B230FT (SOLD)
'88 Mitsubishi Mighty Max (SOLD)
'91 Kawasaki ZX7 (SOLD)
'95 Kawasaki ZX9R
Did some more wiring. Injectors section. Mock them. Still need to wire into harness. But u get the idea.
Sent from my SM-N920T using Tapatalk
What's the resistor for
'00 Mitsubishi Galant ES 4g64T (Samantha)
'01 Mitsubishi Galant ES 4g64 (Daily)
'02 Mitsubishi Galant ES 4g64 (SCRAPPED)
'00 Mitsubishi Galant ES 4g64 (SCRAPPED)
'91 Volvo 740 Turbo B230FT (SOLD)
'88 Mitsubishi Mighty Max (SOLD)
'91 Kawasaki ZX7 (SOLD)
'95 Kawasaki ZX9R
Injectors. Evo8 560cc. Instead of have a used or faulty big box in the bay. I use this resistors for a cleaner and knowing is new. My piece of mind.
(Remember when i ask if dsm and evo are same resistance) i have used this many times for low impendace injectors.
Sent from my SM-N920T using Tapatalk
'00 Mitsubishi Galant ES 4g64T (Samantha)
'01 Mitsubishi Galant ES 4g64 (Daily)
'02 Mitsubishi Galant ES 4g64 (SCRAPPED)
'00 Mitsubishi Galant ES 4g64 (SCRAPPED)
'91 Volvo 740 Turbo B230FT (SOLD)
'88 Mitsubishi Mighty Max (SOLD)
'91 Kawasaki ZX7 (SOLD)
'95 Kawasaki ZX9R
I like the idea and never had an issue with these.
Sent from my SM-N920T using Tapatalk
any luck with that manifold spacer? ive got a couple of those flanges laying around as well and was thinking of doing the same thing.
Yes i mount it and cleared. I have to do some sanding and coating once is all done i will take better pictures.
Sent from my SM-N920T using Tapatalk
Been super busy. My cars decided to break all at the same time. So now all done and working good. Time to get this out of here, tired of lookin at it. If is just 10 mins a day, i will get this car done. Clean and did some organizing.
Sent from my SM-N920T using Tapatalk
Full wired coils and injectors.
Sent from my SM-N920T using Tapatalk
Cam and coolant sensor wired
Sent from my SM-N920T using Tapatalk
Bookmarks