devgrp
01-10-2006, 08:15 AM
Yesterday I got a good deal on a pair of 05 LS 430 Lexus headlights. I got the bulbs, projectors and ballasts. According to a lot of people these projectors are suppose to be very good with a very wide beam.
The problem is that to acheive this wide out, the projector uses a reflector below the projector. Now I was thinking about cutting this off, but I did some measurements and it seem with some good hacking I should be able to get it to fit. These are not my pics, but here is what they look like.
Wide beam
http://img274.echo.cx/img274/4255/pix103ej.jpg
http://img274.imageshack.us/img274/1029/pix96fv.jpg
Projectors with reflector (ls430 projector on the left)
http://img192.echo.cx/img192/192/ls4309au.jpg
I will be doing some research, then I will attempt this monsterous feat this weekend. Wish me luck https://www.thegalantcenter.org/style_emoticons/default/biggrin.gif
**UPDATE**
I made a harness last night but it did'nt work. I think the wires were too long, so this morning I made a new one with shorter wires. This is the diagram I used for my harness
http://i14.photobucket.com/albums/a303/plugsnet/WireHarness.jpg
This is where I had the problem. In the diagram it is showing that pin 85 goes to the 12v pin on the stock harness. That wont work. The stock wiring is activated via a relay in the fuse box, so enough power was not being sent to the ballast. What I did was connect pin 85 to one of the low beam fuse, thus bypassing that stock relay.
Here are some pics
http://img.photobucket.com/albums/v662/devgrp/IMG_5338.jpg
http://img.photobucket.com/albums/v662/devgrp/IMG_5337.jpg
http://img.photobucket.com/albums/v662/devgrp/IMG_5343.jpg
http://img.photobucket.com/albums/v662/devgrp/IMG_5339.jpg
The problem is that to acheive this wide out, the projector uses a reflector below the projector. Now I was thinking about cutting this off, but I did some measurements and it seem with some good hacking I should be able to get it to fit. These are not my pics, but here is what they look like.
Wide beam
http://img274.echo.cx/img274/4255/pix103ej.jpg
http://img274.imageshack.us/img274/1029/pix96fv.jpg
Projectors with reflector (ls430 projector on the left)
http://img192.echo.cx/img192/192/ls4309au.jpg
I will be doing some research, then I will attempt this monsterous feat this weekend. Wish me luck https://www.thegalantcenter.org/style_emoticons/default/biggrin.gif
**UPDATE**
I made a harness last night but it did'nt work. I think the wires were too long, so this morning I made a new one with shorter wires. This is the diagram I used for my harness
http://i14.photobucket.com/albums/a303/plugsnet/WireHarness.jpg
This is where I had the problem. In the diagram it is showing that pin 85 goes to the 12v pin on the stock harness. That wont work. The stock wiring is activated via a relay in the fuse box, so enough power was not being sent to the ballast. What I did was connect pin 85 to one of the low beam fuse, thus bypassing that stock relay.
Here are some pics
http://img.photobucket.com/albums/v662/devgrp/IMG_5338.jpg
http://img.photobucket.com/albums/v662/devgrp/IMG_5337.jpg
http://img.photobucket.com/albums/v662/devgrp/IMG_5343.jpg
http://img.photobucket.com/albums/v662/devgrp/IMG_5339.jpg