Customizing Trunk

[thealliance43]

hey my next project on the trunk is to use plexe glass with neons where the spare tire is... figure i'll display the amp and cap in there... and i'm makin a custom box for my 15" l7's on each side by the tail lights. Anyone got pix or ideas that they have done...

[ipaintu]

http://img.photobucket.com/albums/v641/mehlinger/Picture116675.jpg

http://img.photobucket.com/albums/v641/mehlinger/hin/619a711a.jpg


you can see my neons under the trunk lip. I have some in the bottom also to make amps glow at night... I have my cap where you can see it also.. Its easy to do tho... just build a rack for your amps to lay on and then wire it in..
NOW!!!
HEAT!!!!

I have a large house 6 in fan under that glass. I have it to where i can turn my key on and it fires up.. I feel the air flow with no issues. I dont have it mounted just layed in thur... I dont have holes cut into my glass cause i have other ways of air getting out.
The whole bottom board will lift right out and I can get to my amps no issues... Really this is a custom non ported box with some add ons to the sides and top...then side boards for my kicker crossovers....
Im not really finsihed yet I'm just to lazy to finsih it.

If you need more pics yell I will snap some..

[thealliance43]

ya if you can get some more pix i like the fan idea...so you have the plexe not bolted down?that way air can escape? i was gunna do lyke 5 holes....and how'd you power the fan isn't it dc power? did you have to buy that converter from lyke radio shack...caz i got 1 for my playstation...

[milo111000]

http://img.photobucket.com/albums/v641/mehlinger/Picture116675.jpg

http://img.photobucket.com/albums/v641/mehlinger/hin/619a711a.jpg


you can see my neons under the trunk lip. I have some in the bottom also to make amps glow at night... I have my cap where you can see it also.. Its easy to do tho... just build a rack for your amps to lay on and then wire it in..
NOW!!!
HEAT!!!!

I have a large house 6 in fan under that glass. I have it to where i can turn my key on and it fires up.. I feel the air flow with no issues. I dont have it mounted just layed in thur... I dont have holes cut into my glass cause i have other ways of air getting out.
The whole bottom board will lift right out and I can get to my amps no issues... Really this is a custom non ported box with some add ons to the sides and top...then side boards for my kicker crossovers....
Im not really finsihed yet I'm just to lazy to finsih it.

If you need more pics yell I will snap some..


hot shit!!! what rims are those.. diggin them..

[ipaintu]

see you didnt know we had same taste.. Found something we both agree on..

Limited 18" http://www.htawheels.com/product_info.php/...roducts_id/1122 ('http://www.htawheels.com/product_info.php/cPath/1_576/products_id/1122')

Fan is one that plugs into a Cig lighter from store.. I wired a cig plug and then hooked to the remote wire for the amp.. works perfect and no noise other than when you turn it off, I like that tho cause it tells me my fan is still working and im not gonna over heat...
My bottom board isnt bolted down you can remove the whole board to get to the amps... The amps are on a rack built in basicly a large square and longer on the amp side. The screwed to sides of spare wheel housing on a plate i put thur.. Lay the cell so you can see the leds on the bottom shelf.
Then amps on top.. I got in late tonight so no pics ,

Good Luck..

[milo111000]

:wink: :rockon: