mindwerkz
11-17-2007, 11:14 PM
As you may have noticed, I've been too busy with school to spend much time here lately. Here's some of the fruits of that labor. I'm done (for the most part) with the gun I had to build for school. Here are some pix of it in the Hogue stock I bought for it and the wood stock I had to make for it.
Charles Daly 98 Mauser. I barreled it for .300 Winchester Magnum. It currently has a 27.5" barrel but I am going to bring it back to school and cut it down to 20". As part of my specialization project at the end of school I'm going to rebarrel it with a Kreiger #11 contour barrel (basically it'll be 1.25" in diameter the whole way down) and add a flash suppressor set up for a quick detach sound suppressor if I have time after my main specs project. I gave it a bead blasted finish and then blued it all except the trigger, extractor and cocking piece.
http://www.mindwerkz.us/pics/schoolguns/cdmauser1.jpg
http://www.mindwerkz.us/pics/schoolguns/cdmauser2.jpg
http://www.mindwerkz.us/pics/schoolguns/cdmauser3.jpg
http://www.mindwerkz.us/pics/schoolguns/cdmauser4.jpg
http://www.mindwerkz.us/pics/schoolguns/cdmauser5.jpg
So what's my specs project gunna be? I'm gunna build a semi-auto Mark14, Mod0. Basically it's a tricked out M14 in a Sage International Enhanced Battle Rifle stock. The M14 being the full auto version of the M1A, which is the modern version of the M1 Garand, which was our main battle rifle in WWII. I'm dropping no less than $3k in to this badass thang. It's gunna be hardcore. After school I'm gunna give her a QD suppressor (pretty sure no full auto or suppressors at school, yet short barrels are ok, go figure). It's gunna end up looking along these lines but possibly with a shorter barrel and definitely with a Trijicon ACOG scope. Found the perfect night vision accessory for it too. Fits right against the ACOG perfectly. Too bad it's over $8k!!!
http://content.answers.com/main/content/wp/en/e/ec/CSA-2006-10-17-093634.jpg
Charles Daly 98 Mauser. I barreled it for .300 Winchester Magnum. It currently has a 27.5" barrel but I am going to bring it back to school and cut it down to 20". As part of my specialization project at the end of school I'm going to rebarrel it with a Kreiger #11 contour barrel (basically it'll be 1.25" in diameter the whole way down) and add a flash suppressor set up for a quick detach sound suppressor if I have time after my main specs project. I gave it a bead blasted finish and then blued it all except the trigger, extractor and cocking piece.
http://www.mindwerkz.us/pics/schoolguns/cdmauser1.jpg
http://www.mindwerkz.us/pics/schoolguns/cdmauser2.jpg
http://www.mindwerkz.us/pics/schoolguns/cdmauser3.jpg
http://www.mindwerkz.us/pics/schoolguns/cdmauser4.jpg
http://www.mindwerkz.us/pics/schoolguns/cdmauser5.jpg
So what's my specs project gunna be? I'm gunna build a semi-auto Mark14, Mod0. Basically it's a tricked out M14 in a Sage International Enhanced Battle Rifle stock. The M14 being the full auto version of the M1A, which is the modern version of the M1 Garand, which was our main battle rifle in WWII. I'm dropping no less than $3k in to this badass thang. It's gunna be hardcore. After school I'm gunna give her a QD suppressor (pretty sure no full auto or suppressors at school, yet short barrels are ok, go figure). It's gunna end up looking along these lines but possibly with a shorter barrel and definitely with a Trijicon ACOG scope. Found the perfect night vision accessory for it too. Fits right against the ACOG perfectly. Too bad it's over $8k!!!
http://content.answers.com/main/content/wp/en/e/ec/CSA-2006-10-17-093634.jpg