remarque
10-21-2008, 07:00 PM
Well after I bought the 1991 Talon Tsi with a bad engine and it did turn out so well. Sold it to a junk yard for $150, after taking the 390cc injectors, turbo manny, resistor pack and some other stuff. Sold most of the stuff on Ebay to make some more of my money back, since I only paid $340 for it and that was towed to me.
After doing more research I found this 1993 Mitsubishi Mirage. I paid $550 for it and drove it home. The 1.5 engine was not responsive at, but when it did respond the Mirage was out pacing the Galant. I got it so cheap because it had an oil leak, that the owner didnt know where it was coming from. After looking over the car I found it had a bad rear main seal, instead of trying to replace I search the net and found Mirage Performance.
At Mirage Performance found a number of swaps I could do, the 4g64,4g63 and 4g63T were the swaps I was looking into. I decided with the 4g64 because the engine and parts were cheap and easy to find. The 4g63 required you to cut and weld the motor mount to get it to fit. I found a 4g64 from and Mitsubishi Expo with 113K on the clock for $200 and I'm using a 1.8 manual tranny from a 1994 Mirage. The Galant tranny required fabrication of the top tranny mount and custom axles, the 1.8 tranny is a direct swap and right on the 4g64.
Pic when I first got the car, super clean.
http://farm4.static.flickr.com/3245/2607843817_04ff533a62.jpg
http://farm4.static.flickr.com/3098/2607843823_21060acd76.jpg
http://farm4.static.flickr.com/3283/2607843825_bc087a7c9b.jpg
http://farm4.static.flickr.com/3196/2607843829_a07d317f82.jpg
A trip to the Pull-A-Part, I got 5 speed cables, Pedals, Hyrdo Clutch and MAS. Second pic is the 4g64 in the trunk of the Mirage.
http://farm4.static.flickr.com/3136/2702200253_64fbabf602.jpg
http://farm4.static.flickr.com/3170/2704808016_8d8021a1f4.jpg
Pulling the 1.5 engine out
http://farm4.static.flickr.com/3254/2928714903_b72810c215.jpg
The 2.4 finally in.
http://farm4.static.flickr.com/3024/2928715197_bef577ab56.jpg
http://farm4.static.flickr.com/3190/2929578912_8fbfd410bc.jpg
Had to take the tranny back out because I got the wrong drive plate. I had one for a Galant, but needed one for a 1.8 Mirage.
http://farm4.static.flickr.com/3212/2962234865_227a73e1a8.jpg
And to add I was using my 1.5 tranny mounts and they were not fitting right, as you can see in the picture I had to remove those. After I got the new drive plate on, I found it hard as hell to get the tranny back on. I had to remove the engine again and put the tranny on while it was out the car. The engine is in car now, but now the engine mount is wrong. The Galant 4g64 and Expo 4g64 are the same, but some bits and pieces are different. Like the throttle body is flipped 180 degrees, the motor mount bolts are different and intake manifold is backwards.
http://farm4.static.flickr.com/3154/2962234979_bdb0c756c7.jpg
http://farm4.static.flickr.com/3286/2963081750_7d708ed3ac.jpg
Everything is in the car still gotta fix the motor mount and wire everything up. Will have new pic tomorrow.
After doing more research I found this 1993 Mitsubishi Mirage. I paid $550 for it and drove it home. The 1.5 engine was not responsive at, but when it did respond the Mirage was out pacing the Galant. I got it so cheap because it had an oil leak, that the owner didnt know where it was coming from. After looking over the car I found it had a bad rear main seal, instead of trying to replace I search the net and found Mirage Performance.
At Mirage Performance found a number of swaps I could do, the 4g64,4g63 and 4g63T were the swaps I was looking into. I decided with the 4g64 because the engine and parts were cheap and easy to find. The 4g63 required you to cut and weld the motor mount to get it to fit. I found a 4g64 from and Mitsubishi Expo with 113K on the clock for $200 and I'm using a 1.8 manual tranny from a 1994 Mirage. The Galant tranny required fabrication of the top tranny mount and custom axles, the 1.8 tranny is a direct swap and right on the 4g64.
Pic when I first got the car, super clean.
http://farm4.static.flickr.com/3245/2607843817_04ff533a62.jpg
http://farm4.static.flickr.com/3098/2607843823_21060acd76.jpg
http://farm4.static.flickr.com/3283/2607843825_bc087a7c9b.jpg
http://farm4.static.flickr.com/3196/2607843829_a07d317f82.jpg
A trip to the Pull-A-Part, I got 5 speed cables, Pedals, Hyrdo Clutch and MAS. Second pic is the 4g64 in the trunk of the Mirage.
http://farm4.static.flickr.com/3136/2702200253_64fbabf602.jpg
http://farm4.static.flickr.com/3170/2704808016_8d8021a1f4.jpg
Pulling the 1.5 engine out
http://farm4.static.flickr.com/3254/2928714903_b72810c215.jpg
The 2.4 finally in.
http://farm4.static.flickr.com/3024/2928715197_bef577ab56.jpg
http://farm4.static.flickr.com/3190/2929578912_8fbfd410bc.jpg
Had to take the tranny back out because I got the wrong drive plate. I had one for a Galant, but needed one for a 1.8 Mirage.
http://farm4.static.flickr.com/3212/2962234865_227a73e1a8.jpg
And to add I was using my 1.5 tranny mounts and they were not fitting right, as you can see in the picture I had to remove those. After I got the new drive plate on, I found it hard as hell to get the tranny back on. I had to remove the engine again and put the tranny on while it was out the car. The engine is in car now, but now the engine mount is wrong. The Galant 4g64 and Expo 4g64 are the same, but some bits and pieces are different. Like the throttle body is flipped 180 degrees, the motor mount bolts are different and intake manifold is backwards.
http://farm4.static.flickr.com/3154/2962234979_bdb0c756c7.jpg
http://farm4.static.flickr.com/3286/2963081750_7d708ed3ac.jpg
Everything is in the car still gotta fix the motor mount and wire everything up. Will have new pic tomorrow.