Zigens 7G build thread

[ZigenScarface]

Now that circuit city went under ill have the time needed to start and finish my 7g... Over the next few weeks ill be posting progress and i hope to move pretty fast with it. Any comments, positive or negative are welcomed as well as ideas, dont be afraid to speak up i assure you i wont lose any sleep over it!
Also this is going to be a full build and i know its messy now but it will be cleaned up so dont worry about that..

All of this was done yesterday when i found 2 hours of free time between errands.
Out with the 275's and in with the 450's
http://c2.ac-images.myspacecdn.com/images02/33/l_bb92c9611e954c738aa2aa87d9abeabd.jpg
Again with resistor pack (not installed yet)
http://c1.ac-images.myspacecdn.com/images02/14/l_308993f530f045d993ee827786ca4c50.jpg
Fuel rail out
http://c2.ac-images.myspacecdn.com/images02/36/l_64f6422cbabc482a95cf3e61723754b9.jpg
Fuel rail back in and test fit vr-4 strut bar
http://c4.ac-images.myspacecdn.com/images02/53/l_cb80bcb981804c92962a57bc1a9dd567.jpg
Maft mounting location
http://c3.ac-images.myspacecdn.com/images02/29/l_8f397a971311477fb5a4bcff3f5b76ce.jpg
Teaser pic
http://c1.ac-images.myspacecdn.com/images02/25/l_069ece4e6998432aa52b359fc9be5070.jpg
Vr4 wing FTW
http://c4.ac-images.myspacecdn.com/images02/13/l_c81654c854294ade8c5b690c30ddd81f.jpg
And another
http://c4.ac-images.myspacecdn.com/images02/16/l_32d9083549334c088328756ee1f743d3.jpg
And project for 2morrow if its nice out
http://c4.ac-images.myspacecdn.com/images02/58/l_5ff5aa7a0ba34110b592e54be8163c57.jpg
-Python 460 hp security and keyless entry
-Audio sensor
-Dual zone motion sensor
-4x Door lock actuators
-Trunk release
-2x Relays

I may also run my FMIC pipe 2morrow..

[kolio]

you had manual locks and windows too?


coming along nicely. does your strut brace hit the hood? i had to trim the skeleton unter the hood

[ZigenScarface]

you had manual locks and windows too?


coming along nicely. does your strut brace hit the hood? i had to trim the skeleton unter the hood

yea manual everything... in that pic the strut bar isisnt bolted down but by the looks of it its going to hit.. im not sure how often ill have my hood on tho

[mko]

Take a pic of the front bumper, what lip is that? Vr4 spoiler looks sexy

[greddy]

what's with the horsepower in a box, didu really buy one of those ebay horsepower "booster chips"

[ZigenScarface]

Take a pic of the front bumper, what lip is that? Vr4 spoiler looks sexy

teaser untill i mold n finish it!


what's with the horsepower in a box, didu really buy one of those ebay horsepower "booster chips"

heh not really... its to run a gm mas in place of a mitsu mas...
easier to use with intercooler pipe, adjustment for larger fuel injectors, ect.. its actually maft pro so i have the controller mounted in the car under the arm rest but its not wired up completely.. ill post pics of that when its done as well

[njjfudge]

what's with the horsepower in a box, didu really buy one of those ebay horsepower "booster chips"


That is a MAF translator box........................

[Galant306m]

That is a MAF translator box........................

Yes

Looks good man, Just take some full pictures of your car.

[4-G-rim]

what's with the horsepower in a box, didu really buy one of those ebay horsepower "booster chips"


http://www.fullthrottlespeed.com/itemdesc.asp?ic=050DSMTRANS2G3S

[greddy]

^thanks for clearing that up, I saw a horsepower chip on ebay that looked just like that, that's why I asked.

[kolio]

yea manual everything... in that pic the strut bar isisnt bolted down but by the looks of it its going to hit.. im not sure how often ill have my hood on tho

ya just like mine, it sucks right? PM me where you got the alarm and locks. my ebay system took a crap and i need a new one asap!

and the for the strut brace all you need to do is trim the skeleton. i will get you a pic

[mko]

yeah, post a pic, cuz i just ordered the strut bar

[ZigenScarface]

ya just like mine, it sucks right? PM me where you got the alarm and locks. my ebay system took a crap and i need a new one asap!

and the for the strut brace all you need to do is trim the skeleton. i will get you a pic

yeh whatd u need to kno? did u want help finding a nice unit or info with wires? i can provide any of that info lol

[4g63lover]

all this time I thought you had a JDM'd out 8G

[ZigenScarface]

i do.. well i did alot of stuff is sold off of it and its going back to usdm body style

[kolio]

yeh whatd u need to kno? did u want help finding a nice unit or info with wires? i can provide any of that info lol

i have wired the system before but both would be great!

[Goku]

Looking good man =)

[ZigenScarface]

so i wired up my resistor pack today, started it up and smoke was pouring out the exhaust.. popped the oil lid n there was white cloudyness in the oil... so time for a full engine build n not just a "bolt on turbo" setup :(
lookin to buy a 4g64 (for a 95) if anyone is selling one thats in good running condition let me know!

[Galant306m]

so i wired up my resistor pack today, started it up and smoke was pouring out the exhaust.. popped the oil lid n there was white cloudyness in the oil... so time for a full engine build n not just a "bolt on turbo" setup :(
lookin to buy a 4g64 (for a 95) if anyone is selling one thats in good running condition let me know!

If you want to build a sohc head ill give you mine after i pull it off next month. and then just do rings and bearings with a cylinder hone and you should be set.

[KaziKai]

nice! I wished that strut bar fitted my g....

[Galanttuner10]

nice! I wished that strut bar fitted my g....

im pretty sure that strut bar does fit the 8g as well

and zigen nice job dude it was nice 2 finally c pics of it.. my turbo is going in this week hahaha..

cant wait til u finish bro keep it up!!!!

[kolio]

im pretty sure that strut bar does fit the 8g as well

and zigen nice job dude it was nice 2 finally c pics of it.. my turbo is going in this week hahaha..

cant wait til u finish bro keep it up!!!!

no it doesn't. the USDM 8G is diffrent suspension. thats a fact.

[ZigenScarface]

i jus dipped in my "same money im unemployed" fund and ordered some goodies.. =p

[Galanttuner10]

no it doesn't. the USDM 8G is diffrent suspension. thats a fact.

alright good enough 2 me

[bmore303]

so i wired up my resistor pack today, started it up and smoke was pouring out the exhaust.. popped the oil lid n there was white cloudyness in the oil... so time for a full engine build n not just a "bolt on turbo" setup :(
lookin to buy a 4g64 (for a 95) if anyone is selling one thats in good running condition let me know!


I'm almost certain you don't need a rebuild. you put 450cc injectors on an ecu programmed for 275cc. Now upon immediate startup you saw smoke, you're running rich as expected. You need to tune the car to accept the 450's. You should just have gas in your oil from drowning the poor thing.

[ZigenScarface]

http://i16.ebayimg.com/01/i/001/24/af/dd8c_1.JPG
http://i22.ebayimg.com/02/i/001/24/af/dde6_1.JPG
http://i6.ebayimg.com/02/i/001/24/af/de4e_1.JPG
http://i24.ebayimg.com/03/i/001/24/af/e09f_1.JPG
http://i5.ebayimg.com/07/i/001/24/af/e2d4_1.JPG

just got this yeayy
intake increased 15% cfm
echaust increased 20% cfm
comes with cam, followers, new stem seal, and 3 angle valve job..
coming my way should have it on friday.. also ordered a 20g and all components to install
[/URL][URL="http://i6.ebayimg.com/02/i/001/24/af/de4e_1.JPG"] (http://i24.ebayimg.com/03/i/001/24/af/e09f_1.JPG)

[Galant306m]

status?

Zigen you are the man, man. Atleast you dont have to close your thread cause you pictures suck right?

[KaziKai]

Hey did you installed the strut bar yet?

[starh4x]

status?

Zigen you are the man, man. Atleast you dont have to close your thread cause you pictures suck right?

LOOOOOOOOOOOOOOOOOOOOOOOOOOOOL!!!!!!!!!!!! :smt081

[ZigenScarface]

oh yeh lol.. ill post some updates in a few mins haha

[Galant306m]

lies

[bmore303]

This topic is full of fail and aids ._.

[ZigenScarface]

sorry beeen sick ll day lol didnt take the cover off at all

[ZigenScarface]

put my MAFT in for a few seconds to test it out.. wires are not perminate lol just tested
http://c2.ac-images.myspacecdn.com/images02/94/l_3c74a7ff020c41c699e466bdc32ec88d.jpg

short throw shifter in
http://c4.ac-images.myspacecdn.com/images02/67/l_9c3a96ceab6a40258d86f324d6c50c2f.jpg

[bronxbombr]

Yo Gary i like! are you gonna remold another carpc for the 7G? If so i think i already have a spare bezel laying around somewhere.

[ZigenScarface]

ha im not sure what im d oing audio wise yet al.. it would be nice for tuning.. u godda come up my way one of these days.. also i got a lift and garage w spray booth in yonkers ;)

[peanotation]

question. so you put the maft in...i assume you also have the translator? and how did you wire it into the car....straight into the ECU? or is there a seperate tuning device on top of all of this??

[ZigenScarface]

the maft is plug and play minus one wire, the controller you tap goes into the ECU, its a seperate piece, not the translator its self

[phizzalot]

looking good... that built sohc looks pretty nice as well, any idea on what gains your getting from it?