Megan Racing Front tie bar

[Bring380GT]

So I have searched Club3g and here but has anyone installed a Megan Racing Front tie bar?:spinner:
and if so any pics? or can someone tell me where it connects too?

[mrg7243]

just looking at it im going to say it goes over the front sway bar, but im not sure exactly

[Bring380GT]

just looking at it im going to say it goes over the front sway bar, but im not sure exactly

See thats what I'm not sure about I have my car on the lift no motor or anything in it yet and I still really can't see where it would go I know it says front tie bar lol still can't see it

[mrg7243]

http://en.wikipedia.org/wiki/Lower_tie_bar
http://www.corsportusa.com/store/catalog/images/DSC04717x8.jpg
heres what i found, the picture is off a civic but i think the concept is the same, it bolts to the bottom of the control arms, i dont have a picture of the underside of my car but it might interfere with the front sway bar

[Joshua42007]

The tie bar/ tie rod installs underneath the trunk between the rear axles or front axles, depending on whether it’s a front or rear tie bar.

[Joshua42007]

http://www.hspnnews.com/images/uploads/Nukabetotal_evo.jpg

[G-spot]

Rear tie bar will fit, yes and it was made to fit the 2g Eclipse which by the way the 3G/8g platforms uses the similar rear suspension setup. As for the front, no, as it was designed as a different platform (hence the different engine/strut configurations). I'm talking about tie bar made of one bar like an underbrace.

You can ask COMPLX to make one but the way he hadled the 1st GB I'm not too sure about it.

[Bring380GT]

Wesellcarparts.com sells a Megan Front tie bar for 00 to 05 eclipse so I know it will work

[Exhaust power]

revival:

I was on ebay and i bumped into these.
http://cgi.ebay.com/ebaymotors/97-03-MITSUBISHI-GALANT-FRONT-LOWER-TIE-BAR-TOWER-BRACE-/220652312155?pt=Motors_Car_Truck_Parts_Accessories #ht_5227wt_1002

I might pick them up if they fit. right now i messaged the seller to see whats up with them.

[mrg7243]

i dont trust the universal fit

[Exhaust power]

doesnt fit send it back right? ill see what he says about it.

[Ruslik]

universal fit. made out of aluminum i dk i dont think it will do much

[Exhaust power]

probably not but itll look good lol

[Joshua42007]

It is adjustable. if you can, try and get one that is a solid 1 piece. Strut bars that are solid, are better. If the bar doesn't have a spot to flex, it will be stronger and more efficient.

heres an example, this strut bar can be adjusted.
http://i242.photobucket.com/albums/ff285/liew8888/murah2u/cuscofrontrearstrutbarforwira2.jpg

this one is non adjustable
http://i38.photobucket.com/albums/e148/super17xxx/014.jpg

[G-spot]

This thread is about the lower front tie bar not the front strut bar

I searched around club3g and the holes fit fine. The problem is the exhaust flex pipe is in the way. I don't know if they found a way to fix that yet.

[Joshua42007]

I know that, im just speaking for strut bars in general.

[G-spot]

well, thanks for the clarify

[Joshua42007]

:ironchiefwilly3: Lol i should have done that earlier

[Stewi]

I cant see it helping much being that it probably mounts what, lets say a foot away from the main subframe? How much body flex is really going on down there that close to a giant double reinforced steel subframe? I doubt enough to notice. Its like the rear lower tie bar that mounts to the solid steel rear crossmember, purely cosmetic. Im not gonna lie I like the look of the rear one, but its all for look, not functionality. The old kit that company used to make with a bunch of underbrace bars would help because it braces more of the center of the car which isnt near the subframes.

[Exhaust power]

I would love for some one to check out my car when its jacked up. and wow them with all suspension mods lol

but yeah i agree with you on it mostly being for looks