RIgalant
10-19-2012, 04:27 PM
Sick if the tangled wires around my shifter i decided to clean it up alittle and hide the wire, it was very very simple and took my about 20 mins and the end result was very clean cut. all you need is:a 3ft usb extender from best buy, radio shack or walmart it doesnt matter, a soldering pen or drill with a big enough bit, philips head screw driver, and a flat head screw driver.
1- Remove the center console piece such the radio trim, shifter trim and cigarette lighter trim. they all pop out with no screws holding them in.
https://sphotos-a.xx.fbcdn.net/hphotos-ash3/579175_3723010760711_254301966_n.jpg
as you see the radio trim pops out with a little muscle.
2- Remove the cup holder by loosening the two philips head screws under the arm rest
https://sphotos-a.xx.fbcdn.net/hphotos-ash4/486709_3723012840763_1573936570_n.jpg
3- With the arm rest/cup holder out, get the soldering pen hot to melt the plastic. i made a rough hole but the black rubber mat hides the hole well. or you can use a drill with a large enough bit for the usb port. like in the picture above. now cut a spot in the black mat to get the cord through
https://sphotos-b.xx.fbcdn.net/hphotos-prn1/553735_3723013360776_2078358035_n.jpg
4- Run the cords under the center console with the usb extender plugged into the radio. (you will need the extender for the usb port, i tried with the regular 3 foot iPod cable its just a twat hair short. and the AUX cord should be at least 5ft or more)
5-MAKE SURE IT WORKS!!!! before you button everything up make sure the iPod or what ever plays!
6-Button it up! :]
This was my first sorta-Tutorial
End Results may vary :p
https://sphotos-b.xx.fbcdn.net/hphotos-ash3/564836_3723014320800_743222347_n.jpg
https://sphotos-b.xx.fbcdn.net/hphotos-ash3/598804_3723015360826_665277602_n.jpg
1- Remove the center console piece such the radio trim, shifter trim and cigarette lighter trim. they all pop out with no screws holding them in.
https://sphotos-a.xx.fbcdn.net/hphotos-ash3/579175_3723010760711_254301966_n.jpg
as you see the radio trim pops out with a little muscle.
2- Remove the cup holder by loosening the two philips head screws under the arm rest
https://sphotos-a.xx.fbcdn.net/hphotos-ash4/486709_3723012840763_1573936570_n.jpg
3- With the arm rest/cup holder out, get the soldering pen hot to melt the plastic. i made a rough hole but the black rubber mat hides the hole well. or you can use a drill with a large enough bit for the usb port. like in the picture above. now cut a spot in the black mat to get the cord through
https://sphotos-b.xx.fbcdn.net/hphotos-prn1/553735_3723013360776_2078358035_n.jpg
4- Run the cords under the center console with the usb extender plugged into the radio. (you will need the extender for the usb port, i tried with the regular 3 foot iPod cable its just a twat hair short. and the AUX cord should be at least 5ft or more)
5-MAKE SURE IT WORKS!!!! before you button everything up make sure the iPod or what ever plays!
6-Button it up! :]
This was my first sorta-Tutorial
End Results may vary :p
https://sphotos-b.xx.fbcdn.net/hphotos-ash3/564836_3723014320800_743222347_n.jpg
https://sphotos-b.xx.fbcdn.net/hphotos-ash3/598804_3723015360826_665277602_n.jpg