Installation of additional devices.

Again hello everyone! I plan to install the compressor in my car. For the correct settings I need to install the wideband O2 metr (next WBO2) and sensor boost. In this topic I want to talk about it. Again I apologize for my English. So, to start acquired two sensor DEPO RACING. That's the way they appear on the table http://s013.radikal.ru/i324/1107/04/e53834959952.jpg http://s41.radikal.ru/i094/1107/40/0a1d54156f0f.jpg http://s011.radikal.ru/i316/1107/15/b5bccc21db78.jpg The devices are manufactured in Taiwan for the japanese market.

You must first install themselves sensors.WBO2 I decided to install in front of the rear catalyst.Create layout and make the hole. http://s008.radikal.ru/i304/1107/ce/fff0ae382b48.jpg http://s007.radikal.ru/i302/1107/d4/b07c5c26785f.jpg

It is necessary to correctly wasted hole. The nut should firmly established http://i063.radikal.ru/1107/70/e99206cc4ea2.jpg http://s60.radikal.ru/i170/1107/e2/0967850edfb0.jpg http://s016.radikal.ru/i335/1107/2c/56b49c281812.jpg[/

Sensor rests in the thermal cover.It is also necessary to make a hole.http://i047.radikal.ru/1108/30/1c851d33ba36.jpg http://s016.radikal.ru/i336/1108/7a/011ad26f43b4.jpg And set himself sensor. Wire of the sensor will go under the hood and is mounted to the engine shield. http://s015.radikal.ru/i330/1108/0e/abc3ac4dc541.jpg

Can't understand why the images are so large. Moderators, can adjust these images?

Sensor boost for instructions connected to the vacuum hose to the inlet manifold.But on the engine 4G69 no vacuum hoses at all. So I had to turn on a lathe that kind of detail.http://i078.radikal.ru/1107/cc/ccc5159c6e1f.jpg Together with the sensor in the kit there is a small filter. http://s50.radikal.ru/i129/1107/e0/2fae4cb6fe39.jpg.

Do the hole and cut the threads in a convenient location on the manifold.http://s40.radikal.ru/i089/1107/c1/ceaceecea4ec.jpg http://i037.radikal.ru/1107/67/47f262b18bc7.jpg http://i065.radikal.ru/1107/13/1cf0f1bb7c29.jpg. Assign a sensor in the engine shield, and connect the vacuum tube. http://s45.radikal.ru/i110/1107/ee/609804b9d4d8.jpg In the future to the tube so as to enable the valve blow off

So the sensors are installed. Now you need to install devices in the salon. I decided to install them in front of the left rack. I do not know how to English it is called a substance, but in Russian it is called plastilin. Apply for the children's creativity. Attach the glass and замазываю the cracks of plasticine. http://s59.radikal.ru/i163/1107/76/87a257bd7cda.jpg http://s009.radikal.ru/i309/1107/31/a47078af69a5.jpg http://s41.radikal.ru/i094/1107/0a/23505e7937dd.jpg

On the reverse side of the I I fasten it two screws http://s56.radikal.ru/i152/1107/e1/ef8accb04194.jpg The screws will hold the glass. And completely close the detail of a paper tape. http://s014.radikal.ru/i328/1107/cc/5ffbf8d3a7bd.jpg

Then I use resin and glass mats. Enough place a 3 layer. After the resin dries, start the processing. http://s41.radikal.ru/i093/1107/01/2f1e4405ba1f.jpg http://i057.radikal.ru/1107/c3/bf6c5c957f09.jpg http://s43.radikal.ru/i101/1107/29/35bfb7e9de59.jpg http://s48.radikal.ru/i122/1107/97/a0c1c1f7a313.jpg

I have the fabric of which is covered with a torpedo. Cut pattern and glue on the glass. http://i044.radikal.ru/1107/d0/96d349a3c741.jpg http://s011.radikal.ru/i317/1107/c8/b14c2ba13784.jpg

That's the way it looks. http://i022.radikal.ru/1107/3e/4a2ace63a1b1.jpg http://s07.radikal.ru/i180/1107/13/e0aef7f320b8.jpg

The second glass is done the same way. http://s42.radikal.ru/i097/1108/33/700745f410f4.jpg http://s002.radikal.ru/i200/1108/af/8e16db0a922c.jpg

Then connect the devices to the sensors. Now I see how it is formed of fuel-air mixture and the pressure in the intake manifold.http://s015.radikal.ru/i333/1108/85/ff6422e40548.jpg

Here's another video of how it works. 12082011009
Now I am ready to set up the engine. But this is the next step. On this until the finish. Waiting for your comments. If it is someone interesting.