If you don't follow me on Facebook. I recently added leather interior. And it feels good
Printable View
If you don't follow me on Facebook. I recently added leather interior. And it feels good
I loled a little comes off like you think youre Vin Diesel or somethingQuote:
Originally Posted by finald8ta
Lmao
Nice. Did you get a 3G or Evo fitment rad? How is quality?Quote:
Originally Posted by M-Rod
It's actually a Civic half-size radiator. It was required due to my turbo placement in order to keep the amount of piping to a minimum. It should be on my doorstep within a week. I'll be able to report back about it's quality at that time.
You should have told me you need a half size! I have one literally just sitting in my garage. It's a blackworks though.
Got the wideband installed, been slacking on getting a tune but it's just sitting in the garage while I'm at school
https://farm8.staticflickr.com/7454/...75993439_c.jpg
Is that a custom shift knob?Quote:
Originally Posted by Guzm4n
Tapatalk on iOS
It's a TWM Desert Eagle shift knob
Pulled the starter and cleaned it, pulled the exhaust manifold and spit shinned it, replaced the headlight connectors, drained old radiator fluid.......then noobed it up and broke the power bolt on the starter solenoid 😩
http://tapatalk.imageshack.com/v2/15...ae042f00fb.jpghttp://tapatalk.imageshack.com/v2/15...468da03d1f.jpg
I have an addiction to 8G's
That looks awsome.
Thanks, not as awesome as a fixed electrical issue though lol. Day off today, I need to actually work at some point this week [emoji86]Quote:
Originally Posted by coconut
I have an addiction to 8G's
Got some new struts and springs installed as well as a new cv axle. No more bottoming out!
http://tapatalk.imageshack.com/v2/15...f8c77613be.jpg
http://tapatalk.imageshack.com/v2/15...4c1069ce92.jpg
Nice.
Got a "chrome" intake put in today. Sold the black to Nathan. Not sure if I like it more or not but oh well...it's different.
http://tapatalk.imageshack.com/v2/15...4effed52c4.jpg
And got this in the mail...73 wires...now I have to wait on BJ to send me the galant ecu I bought few weeks back to make a conversion harness =D
http://tapatalk.imageshack.com/v2/15...6141717b0d.jpg
Sent from my iPhone using Tapatalk
Nice, dood.
Halfway there!
http://tapatalk.imageshack.com/v2/15...8823badd78.jpg
[emoji106]Quote:
Originally Posted by rezyy0
I have an addiction to 8G's
So I broke the copper bolt on the starter the other day. Today I took a copper nut and was able to grab the end of what was still on the solenoid and thread it on. Then threaded on the rest of the copper bolt end that broke off and it was as good as new. Well maybe not that good, but good enough to work until I get a new starter.
Painted battery plate, painted calipers and I'm about to throw on some new rotors up front. Last thing is to add a new silicon sealant to the water outlet (thanks coconut for the info).
As Ice Cube once said..... "I gotta say, today is a good day"
I have an addiction to 8G's
Make sure that you have some loctite or something holding that contraption together. Would really suck to have it rattle apart since that's really common
Sent from my iPhone using Tapatalk
That's what I used. It's not going anywhere, but either are my chances of replacing just the solenoid lol.Quote:
Originally Posted by demond0d5
I have an addiction to 8G's
And to add to demond info, I do believe thats a "hot" wire. Could be ugly if it rattled loose.
Remind me again why you have 2 redtops?Quote:
Originally Posted by demond0d5
I can't think of it at the moment. I know your big on audio and your alternator is strong.
I didn't think that the alt I got would be big enough for the amounts of power the system I was building at the time would need. Basically i went with 2 redtops so that on the massive drops that would pull more than the alt could handle the batteries would smooth it out.
Think of the subs as using the same "electrical pattern" as a starter but when the car is running.
Sent from my iPhone using Tapatalk
I'm actually going to drop back down on my system at some point because I never even get close to using what I have...maybe 20% of what it's capable of :/
I did it to say I have it...now I'm gonna go to a custom fiberglass box(s) that hug the wheel arch(s) that weigh a lot less and give me trunk space again ^.^
Then get rid of the factory located battery to make room for piping and clean up the bay a little. But all that is after I get another vehicle, maybe summer project isk
Sent from my iPhone using Tapatalk
I understand all that. I understand audio quite well. I meant why not the yellow tops?Quote:
Originally Posted by demond0d5
Finished! Will update with night pictures later.
http://tapatalk.imageshack.com/v2/15...4ec3001162.jpg
Good job...wasn't too hard right?Quote:
Originally Posted by rezyy0
Prying it apart was horrible. I feel like my fingertips are gonna fall off. But yeah it was pretty easy actually lol.
Ya that part did suck...I know you cant wait till its gets dark lol...I was so anxious...but hopefully you sealed them back up good and if you didnt solder the connections...be sure to do it soon...or have a shop do it...had mine done for like $30 bucks...had clamps at first...not too reliableQuote:
Originally Posted by rezyy0
Yellow tops are deep cycle. If you don't fully cycle a deep cycle then you shorten the life. I won't, and can't, use my audio with the car off. All I use the battery for is startingQuote:
Originally Posted by oakrdrs187
Sent from my iPhone using Tapatalk
Night pictures! Sorry for the glare lol.
http://tapatalk.imageshack.com/v2/15...ff81378831.jpg
http://tapatalk.imageshack.com/v2/15...a6acc82a4c.jpg
And this is in the reflection of the car in front of me lol.
http://tapatalk.imageshack.com/v2/15...bae68e38a9.jpg
That looks awsome!Quote:
Originally Posted by rezyy0
I love some nice halos!
Thanks I appreciate it! It was totally worth the struggle lol.Quote:
Originally Posted by coconut
Bought a new soldering iron today, its got a handy dandy little light on it lol I set about fixing the LED turn signal connectors cause as you guys said, they were shit. Only got the passenger side done before I got cold but the driver side area is a little more cramped by the turn signals so I feel like that will be a bit more of a hassle..
Remove the air box.Quote:
Originally Posted by Techn0Nut1996
Actually the mail problem is the wires are super tight, not sure why tho, but the turn signal barely goes into the slot because the wires are so tight. Is removing the air box hard or require any special tools?Quote:
Originally Posted by oakrdrs187
Just take the top part off and you should be fine. If not the bottom has 3 bolts that are 1/2 inch I think. Super easy. I just changed that bulb like 10 minutes ago lol.Quote:
Originally Posted by Techn0Nut1996
I have an addiction to 8G's
Just reinstalled a stereo deck, I forgot how good these Bose stock systems are! Carry more bass than I thought.
I have an addiction to 8G's