only person that believed
Thank you. Couldn’t have done it without the support of this site. The drive and determination came from all the people telling me I couldn’t do it. Thanks
:098: to all the haters that helped me put this car together
Printable View
only person that believed
Thank you. Couldn’t have done it without the support of this site. The drive and determination came from all the people telling me I couldn’t do it. Thanks
:098: to all the haters that helped me put this car together
Looking good man, that's an amazing transformation already
I can see, keep up the good work
Good stuff man. Talk about a resurrection!
It's clean and nice. Amazing job ! Glad you stayed motivated and brought it back to life.:023:
More mods:
Cut bumper slots, chrome tail pipe slip on
http://i27.photobucket.com/albums/c1...e/IMAG0741.jpg
http://i27.photobucket.com/albums/c1...e/IMAG0742.jpg
Led reverse lights
http://i27.photobucket.com/albums/c1...e/IMAG0739.jpg
wheels came out pretty good!
My new project this holiday season
http://i27.photobucket.com/albums/c1...l/CAM00014.jpg
I have a set of these myself, I'm waiting until I have a place to do the work before I do them, but if you get some extra harnesses you can make yourself a harness to plug into the dome light connector so you don't have to cut any of your factory wires. Good luck and post progress!
Hmm i never thought of cutting the bumper slots...maybe i should do that too. Howd you go about doing it?
Sorta-kinda, yeah. The male plug on the harness that plugs into the front dome light is the same as the one on the harness for the Diamante lights. So, with some extra Diamante harnesses, you can sit in your house and solder together a splitter harness that sends power to your rear lights and solder in a plug to plug into the front dome to keep that functional as well, all without cutting any of your car's wires. Hope this made sense, I'm still waking up.
I think i understand. I drew one up. Is this right?
http://i27.photobucket.com/albums/c1...2-01-49-33.jpg
Sry pic came out big lol
Did passenger side step by step for anyone that wants to do the same.
Start with a cardboard box cut out then trace it in the spot you want them
http://i27.photobucket.com/albums/c1...l/CAM00029.jpg
http://i27.photobucket.com/albums/c1...l/CAM00030.jpg
http://i27.photobucket.com/albums/c1...l/CAM00031.jpg
http://i27.photobucket.com/albums/c1...CAM00035-1.jpg
http://i27.photobucket.com/albums/c1...M00034-1-1.jpg
Good luck and be safe
Doesn't look bad at all, install looks good. Wiring diagram is spot on, just make sure your wires are matched up right, because you have switched grounds with our dome lights as well as the Diamante lights. I see you are using the beige ones on your gray interior, I know it's hard to find a gray set of Diamante lights, but it's possible, just keep looking. I've had three sets of gray and three sets of beige, I have one set of each left, but the gray ones are going in my car. BTW, are those the two-wire Diamante lights or the three-wire ones?
Something I've been working on till i get my springs in.
http://i27.photobucket.com/albums/c1...l/CAM00016.jpg
Before
http://i27.photobucket.com/albums/c1...e/IMAG0704.jpg
After
http://i27.photobucket.com/albums/c1...l/CAM00038.jpg
This is just me messing around with some picture on my new phone
http://i27.photobucket.com/albums/c1...213_122636.jpg
http://i27.photobucket.com/albums/c1...213_121121.jpg
http://i27.photobucket.com/albums/c1...213_123126.jpg