does anybody have the wiring diagram for the 1994 GS (2.4L DOHC)
Printable View
does anybody have the wiring diagram for the 1994 GS (2.4L DOHC)
i know haynes has it, dunno bout chilton
i have chilton i think and it doesn't have pin locations
i have a printout from ALLdata in my room, it has the 94 sohc/dohc pinouts
as well as test parameters for every pin on the ecu.
it used to be hosted on galantspeed.
but..... you'll have to get on Alldata.com to get them now.
Haynes does NOT have the wiring diagram.
what diagram do you need? ecu? coil? what
i need ecu pinout diagramQuote:
Originally Posted by jimskin4
http://i186.photobucket.com/albums/x...4/57432217.gif
http://i186.photobucket.com/albums/x...4/57432216.gif
http://i186.photobucket.com/albums/x...4/57432215.gif
http://i186.photobucket.com/albums/x...4/57432214.gif
http://i186.photobucket.com/albums/x...4/57432213.gif
http://i186.photobucket.com/albums/x...4/57432212.gif
OMG
that is exactly what i needed
much appreciate it, and i want pics of your car too
yeah thats what i have printed out on my desk.
engine bay by chance?
never fails,
dented t-bar
http://i186.photobucket.com/albums/x...urHouse189.jpg
in process of installing turbo. and what dsm would be complete without some good old duct tape....lol
lol duct tape ... that cant fly!
Call me crazy but that wiring diagram doesn't look like the wiring on my 94 ES harness. I've got wires poking out where it says there shouldn't be any, like pins 7 and 13. Whats up?
what colors are they?
did you try cross referencing with the chilton diagram?
Ehhh 13 should be a black System ground wire, I don't have 7 listed for anything, but I believe it's for the automatic transmission "torque reduce request signal"
I bought my mechanic a 6 pack today and he printed out another set of diagrams for me. Here's what I found...
7 = TCU (transmission control unit
10 = "ignition power transistor"
13 = ground
23 = "ignition power transistor"
26 = ground
42 = data link
43 = data link
46 = TCU
58 = knock sensor if you've got a wire there
59 should be blank but I've got a wire there, I'll try to trace it.
61 = sensor +5v for one diagram and TPS for another
69 = crankshaft position OR coolant temp sensor... dunno
72 = coolant temp switch
59 - green /yellow? probably another tranny wire.
61 - Sensor impressed voltage? I never understood this term, but it matches other mitsus so whatever.
69 - Crankshaft Position Sensor
As for 42 and 43 I DID NOT KNOW THAT O.O
You were right about 59 being green yellow and it does go to the TCU connector.
I have no clue what sensor impressed voltage is either, maybe just power? It is labeled as supplying 4.5-5.5v Key On Engine Off.
I'm trying to work out wiring in a 1g Turbo ECU for an AWD swap over on this thread.
Yeah I was looking through my notes, in my situation I'm using the 2g ECU so the sensor impressed voltage was an exact match. That data link connector may be the only thing missing from the OBD 2 in the 94-95...I'll have to check more thoroughly.
when I did my wiring.... If the 1g ecu didn't call for it. then i just put a cap on the 7g wire and moved on.
I have the pinout for the DLC.