Zigens 7G build thread

Printable View

03-19-2009, 10:01 AM
ZigenScarface

Zigens 7G build thread

Now that circuit city went under ill have the time needed to start and finish my 7g... Over the next few weeks ill be posting progress and i hope to move pretty fast with it. Any comments, positive or negative are welcomed as well as ideas, dont be afraid to speak up i assure you i wont lose any sleep over it!
Also this is going to be a full build and i know its messy now but it will be cleaned up so dont worry about that..

All of this was done yesterday when i found 2 hours of free time between errands.
Out with the 275's and in with the 450's
http://c2.ac-images.myspacecdn.com/i...87d9abeabd.jpg
Again with resistor pack (not installed yet)
http://c1.ac-images.myspacecdn.com/i...7786ca4c50.jpg
Fuel rail out
http://c2.ac-images.myspacecdn.com/i...61723754b9.jpg
Fuel rail back in and test fit vr-4 strut bar
http://c4.ac-images.myspacecdn.com/i...bc1a9dd567.jpg
Maft mounting location
http://c3.ac-images.myspacecdn.com/i...ff3f5b76ce.jpg
Teaser pic
http://c1.ac-images.myspacecdn.com/i...9fc9be5070.jpg
Vr4 wing FTW
http://c4.ac-images.myspacecdn.com/i...0c30ddd81f.jpg
And another
http://c4.ac-images.myspacecdn.com/i...6ee1f743d3.jpg
And project for 2morrow if its nice out
http://c4.ac-images.myspacecdn.com/i...4be8163c57.jpg
-Python 460 hp security and keyless entry
-Audio sensor
-Dual zone motion sensor
-4x Door lock actuators
-Trunk release
-2x Relays

I may also run my FMIC pipe 2morrow..
03-19-2009, 10:06 AM
kolio

you had manual locks and windows too?

coming along nicely. does your strut brace hit the hood? i had to trim the skeleton unter the hood
03-19-2009, 10:15 AM
ZigenScarface

Quote:

Originally Posted by kolio

you had manual locks and windows too?

coming along nicely. does your strut brace hit the hood? i had to trim the skeleton unter the hood

yea manual everything... in that pic the strut bar isisnt bolted down but by the looks of it its going to hit.. im not sure how often ill have my hood on tho
03-19-2009, 12:15 PM
mko

Take a pic of the front bumper, what lip is that? Vr4 spoiler looks sexy
03-19-2009, 12:32 PM
greddy

what's with the horsepower in a box, didu really buy one of those ebay horsepower "booster chips"
03-19-2009, 12:38 PM
ZigenScarface

Quote:

Originally Posted by mko

Take a pic of the front bumper, what lip is that? Vr4 spoiler looks sexy

teaser untill i mold n finish it!

Quote:

Originally Posted by greddy

what's with the horsepower in a box, didu really buy one of those ebay horsepower "booster chips"

heh not really... its to run a gm mas in place of a mitsu mas...
easier to use with intercooler pipe, adjustment for larger fuel injectors, ect.. its actually maft pro so i have the controller mounted in the car under the arm rest but its not wired up completely.. ill post pics of that when its done as well
03-19-2009, 12:41 PM
njjfudge

Quote:

Originally Posted by greddy

what's with the horsepower in a box, didu really buy one of those ebay horsepower "booster chips"

That is a MAF translator box........................
03-19-2009, 01:24 PM
Galant306m

Quote:

Originally Posted by njjfudge

That is a MAF translator box........................

Yes

Looks good man, Just take some full pictures of your car.
03-19-2009, 03:50 PM
4-G-rim

Quote:

Originally Posted by greddy

what's with the horsepower in a box, didu really buy one of those ebay horsepower "booster chips"

http://www.fullthrottlespeed.com/ite...50DSMTRANS2G3S
03-19-2009, 04:06 PM
greddy

^thanks for clearing that up, I saw a horsepower chip on ebay that looked just like that, that's why I asked.
03-19-2009, 04:56 PM
kolio

Quote:

Originally Posted by ZigenScarface

yea manual everything... in that pic the strut bar isisnt bolted down but by the looks of it its going to hit.. im not sure how often ill have my hood on tho

ya just like mine, it sucks right? PM me where you got the alarm and locks. my ebay system took a crap and i need a new one asap!

and the for the strut brace all you need to do is trim the skeleton. i will get you a pic
03-19-2009, 05:18 PM
mko

yeah, post a pic, cuz i just ordered the strut bar
03-19-2009, 06:14 PM
ZigenScarface

Quote:

Originally Posted by kolio

ya just like mine, it sucks right? PM me where you got the alarm and locks. my ebay system took a crap and i need a new one asap!

and the for the strut brace all you need to do is trim the skeleton. i will get you a pic

yeh whatd u need to kno? did u want help finding a nice unit or info with wires? i can provide any of that info lol
03-19-2009, 06:48 PM
4g63lover

all this time I thought you had a JDM'd out 8G
03-19-2009, 06:53 PM
ZigenScarface

i do.. well i did alot of stuff is sold off of it and its going back to usdm body style
03-19-2009, 08:31 PM
kolio

Quote:

Originally Posted by ZigenScarface

yeh whatd u need to kno? did u want help finding a nice unit or info with wires? i can provide any of that info lol

i have wired the system before but both would be great!
03-19-2009, 08:41 PM
Goku

Looking good man =)
03-20-2009, 02:41 PM
ZigenScarface

so i wired up my resistor pack today, started it up and smoke was pouring out the exhaust.. popped the oil lid n there was white cloudyness in the oil... so time for a full engine build n not just a "bolt on turbo" setup :(
lookin to buy a 4g64 (for a 95) if anyone is selling one thats in good running condition let me know!
03-20-2009, 03:07 PM
Galant306m

Quote:

Originally Posted by ZigenScarface

so i wired up my resistor pack today, started it up and smoke was pouring out the exhaust.. popped the oil lid n there was white cloudyness in the oil... so time for a full engine build n not just a "bolt on turbo" setup :(
lookin to buy a 4g64 (for a 95) if anyone is selling one thats in good running condition let me know!

If you want to build a sohc head ill give you mine after i pull it off next month. and then just do rings and bearings with a cylinder hone and you should be set.
03-20-2009, 08:56 PM
KaziKai

nice! I wished that strut bar fitted my g....
03-20-2009, 11:54 PM
Galanttuner10

Quote:

Originally Posted by KaziKai

nice! I wished that strut bar fitted my g....

im pretty sure that strut bar does fit the 8g as well

and zigen nice job dude it was nice 2 finally c pics of it.. my turbo is going in this week hahaha..

cant wait til u finish bro keep it up!!!!
03-21-2009, 12:35 AM
kolio

Quote:

Originally Posted by Galanttuner10

im pretty sure that strut bar does fit the 8g as well

and zigen nice job dude it was nice 2 finally c pics of it.. my turbo is going in this week hahaha..

cant wait til u finish bro keep it up!!!!

no it doesn't. the USDM 8G is diffrent suspension. thats a fact.
03-21-2009, 12:40 AM
ZigenScarface

i jus dipped in my "same money im unemployed" fund and ordered some goodies.. =p
03-21-2009, 12:47 AM
Galanttuner10

Quote:

Originally Posted by kolio

no it doesn't. the USDM 8G is diffrent suspension. thats a fact.

alright good enough 2 me
03-21-2009, 05:08 PM
bmore303

Quote:

Originally Posted by ZigenScarface

so i wired up my resistor pack today, started it up and smoke was pouring out the exhaust.. popped the oil lid n there was white cloudyness in the oil... so time for a full engine build n not just a "bolt on turbo" setup :(
lookin to buy a 4g64 (for a 95) if anyone is selling one thats in good running condition let me know!

I'm almost certain you don't need a rebuild. you put 450cc injectors on an ecu programmed for 275cc. Now upon immediate startup you saw smoke, you're running rich as expected. You need to tune the car to accept the 450's. You should just have gas in your oil from drowning the poor thing.
03-21-2009, 08:00 PM
ZigenScarface

http://i16.ebayimg.com/01/i/001/24/af/dd8c_1.JPG
http://i22.ebayimg.com/02/i/001/24/af/dde6_1.JPG
http://i6.ebayimg.com/02/i/001/24/af/de4e_1.JPG
http://i24.ebayimg.com/03/i/001/24/af/e09f_1.JPG
http://i5.ebayimg.com/07/i/001/24/af/e2d4_1.JPG

just got this yeayy
intake increased 15% cfm
echaust increased 20% cfm
comes with cam, followers, new stem seal, and 3 angle valve job..
coming my way should have it on friday.. also ordered a 20g and all components to install
04-22-2009, 01:02 AM
Galant306m

status?

Zigen you are the man, man. Atleast you dont have to close your thread cause you pictures suck right?
04-22-2009, 01:55 AM
KaziKai

Hey did you installed the strut bar yet?
04-22-2009, 02:23 AM
starh4x

Quote:

Originally Posted by Galant306m

status?

Zigen you are the man, man. Atleast you dont have to close your thread cause you pictures suck right?

LOOOOOOOOOOOOOOOOOOOOOOOOOOOOL!!!!!!!!!!!! :smt081
04-22-2009, 10:26 AM
ZigenScarface

oh yeh lol.. ill post some updates in a few mins haha
04-22-2009, 03:03 PM
Galant306m

lies
04-22-2009, 08:28 PM
bmore303

This topic is full of fail and aids ._.
04-22-2009, 10:14 PM
ZigenScarface

sorry beeen sick ll day lol didnt take the cover off at all
04-23-2009, 05:44 PM
ZigenScarface

put my MAFT in for a few seconds to test it out.. wires are not perminate lol just tested
http://c2.ac-images.myspacecdn.com/i...bdc32ec88d.jpg

short throw shifter in
http://c4.ac-images.myspacecdn.com/i...24d6c50c2f.jpg
04-23-2009, 09:55 PM
bronxbombr

Yo Gary i like! are you gonna remold another carpc for the 7G? If so i think i already have a spare bezel laying around somewhere.
04-23-2009, 10:27 PM
ZigenScarface

ha im not sure what im d oing audio wise yet al.. it would be nice for tuning.. u godda come up my way one of these days.. also i got a lift and garage w spray booth in yonkers ;)
04-28-2009, 12:29 AM
peanotation

question. so you put the maft in...i assume you also have the translator? and how did you wire it into the car....straight into the ECU? or is there a seperate tuning device on top of all of this??
04-29-2009, 05:26 PM
ZigenScarface

the maft is plug and play minus one wire, the controller you tap goes into the ECU, its a seperate piece, not the translator its self
04-29-2009, 07:51 PM
phizzalot

looking good... that built sohc looks pretty nice as well, any idea on what gains your getting from it?