How to install Cyber2 Bodykit with pics
Not sure whether it has been posted on here before, but sure enough would help to those who does not want to send their G to the bodyhop to fit the bodykit and are rather do it by themselfes.
Ill start of the rear bamper, and as i progress more ill post more info on here, did not do everething at once due to weather conditions.
#1:
When you will open your boot, carefully remove all of the material that stands on your way, it is the spear wheel cover, material that goes over your tail lights( usually held by plastic screws), also plastic bit that goes over your locking ring.
#2
Remove your taillights to have more access to the stock bamper.
http://img76.imageshack.us/img76/2235/dscn0243zm7.jpg
#3 On either side of the boot, right in the corner you will see some screws there are going to be 3 of them on either side, they will need to be removed as well.
http://img76.imageshack.us/img76/8599/dscn0244cr1.jpg
and some on the left side
http://img89.imageshack.us/img89/7312/dscn0245gr2.jpg
#4 After you remove the plastic bit, you will see that there are 8 more long bolts are holding he bamper, but 4 of them on far side are actually holing little metal rails that support the bamper by plastic clips, they will have to be removed as well otherwise the bamper will not fit properly.
http://img76.imageshack.us/img76/7550/dscn0246oh1.jpg
#5 as i have pulled away the bamper after removing all the bolts and nuts holding it, i noticed that bamper is held by 2 more little bolts underneath. Depending on the age of the car if the bolts are a bit rusty, they must be oiled up a bit in order for you not to brake the head ofthe bold while trying to unscrew it.
http://img89.imageshack.us/img89/1465/dscn0247hl5.jpg
#6
After you will remove your bamper it will look something like this
http://img404.imageshack.us/img404/5372/dscn0248jl6.jpg
As you can see the little rails just under the taillights due to me not knowing that they must be removed, which should have been done while dissasembling the bamper.
#7
After you have removed the bamper make sure you will also unscrew the little protectors that are held by 3 screws and are located on either side of the car by the rear wheels, as bumper should go over this area, and the screws will be used later to hold it to the same plase using same holes that screws were screwd in to.You will only have to drill some holes in the bamper to match those with the holes in the fender.
http://img89.imageshack.us/img89/389/dscn0250fk5.jpg
#8
Your bodykit bamper has 4 bolts coming out the middle of it, those bolts must go in to the holes where the bolts of the standard bamper used to go in to. If the holes do not match to the bolts location, you must predrill new holes or extend the existing once in order for the bodykit to fit properly
#9
When you will fit the bamper, first thing you must do is to put back the tail lights to ensure that bamper is leveled up. Then you may drill the holes on the bamper to match those where little protectors used to be held, and that would require 2 holes on either side of the bodykit, as you have seen in previous pics.
http://img404.imageshack.us/img404/4750/dscn0251ss0.jpg
#10
Next you will notsice that the bamper is not leveld up by where the tail lights meet it, as the bamper would stick out by 5 mil. In order to fix ithis, you will have to ask for a helping hand in order to push in the bamper to close the gap, while you will drill 2 holes on wither side of the boot where standard bolts used to hold the bamper. By placing a couple of small bolts you will fix the problem of gaps on each side
That concludes my tutorial, hope that some of you guys may find it usefull, howevef i do nate take any responsobility if any of you will brake something during this time consuming process.And if you have any questions im more then happy to unswer them.
Once the weather will allow me to dosome work, i will post a tutorial on side skirts installation. 8) 8) 8)
Re: What about the front?
Quote:
Originally Posted by KaziKai
How do you do the front bumper???
well, for him all he has to do is take his stock bumper off and replace it with another. why so simple, you ask? maybe he has a world spec I guess :wink:
