Mrs. 4g63lover's 2010 Mazda3

We've had the Mazda for a little over a year now and she is finally worthy to be posted on the internet.

Mods are as follows:

Eibach Sportlines
ASA KA3 17x7.5 +42
Federal Super Steel 595 225/45/17
Xentec 6000K H.I.D.
Razo shift knob ;)
20% tint all around


http://i10.photobucket.com/albums/a1...3/_MG_2318.jpg

http://i10.photobucket.com/albums/a1...3/_MG_2328.jpg

http://i10.photobucket.com/albums/a1...3/_MG_2329.jpg

http://i10.photobucket.com/albums/a1...3/_MG_2333.jpg

http://i10.photobucket.com/albums/a1...3/_MG_2335.jpg

http://i10.photobucket.com/albums/a1...3/_MG_2337.jpg

http://i10.photobucket.com/albums/a1...3/_MG_2338.jpg

http://i10.photobucket.com/albums/a1...3/_MG_2343.jpg

Going to get an axle-back made as soon as I get the galant's axle-back situated and also going to colormatch all the emblems because mazda thought it was smart to use pins for the emblems and leave holes on the trunk. Also going to tint the taillights red.

The wife's Mazda is looking good Jigz!

Dopeness!

very clean!!

http://i10.photobucket.com/albums/a1...3/_MG_2318.jpg

http://www.smileysnetwork.com/big/biggrin%5B1%5D.gif

even rocking the SoSick logo haha! Looks great man

Nice 3 I just did my wifes front brakes on here's the setup is very interesting and diff from the 8 g, but the fused rotors was a pain. I have a sure fire method for getting stuck rotor off now though. And no her rotors didn't have the bolt holes. Very nice 3

Sent from my BlackBerry 9360 using Tapatalk

Quote:

---

Originally Posted by Rach3T8G

The wife's Mazda is looking good Jigz!

---

Quote:

---

Originally Posted by wetamup2k3g

Dopeness!

---

Quote:

---

Originally Posted by XxGiRLaNT06xX

very clean!!

---

Thank you for the compliments!

Quote:

---

Originally Posted by polishmafia

http://i10.photobucket.com/albums/a1...3/_MG_2318.jpg

http://www.smileysnetwork.com/big/biggrin%5B1%5D.gif

---

HAHAHAHA

Quote:

---

Originally Posted by keith6110

even rocking the SoSick logo haha! Looks great man

---

OF COURSE! We even call the Mazda Baby3! lol

Quote:

---

Originally Posted by bgood12

Nice 3 I just did my wifes front brakes on here's the setup is very interesting and diff from the 8 g, but the fused rotors was a pain. I have a sure fire method for getting stuck rotor off now though. And no her rotors didn't have the bolt holes. Very nice 3

Sent from my BlackBerry 9360 using Tapatalk

---

What year is your wifes 3?

Quote:

---

Originally Posted by bgood12

I have a sure fire method for getting stuck rotor off now though. And no her rotors didn't have the bolt holes.

---

What method? A big fucking hammer? Haha!

Pretty much but get a block of wood and a c clamp clamp the block wood to the face of the rotor with a large piece of plastic or rubber on other side of rotor in case you are reusing it, then bang the hell out of the piece of wood til the rotor moves. If no free do same on other side of rotor like side closer to rear of car and it will come off.

Sent from my BlackBerry 9360 using Tapatalk

I usually use the blunt bit of an air hammer onto the hat. usually does the trick

Yea that would work I have no air tools, but I put some PB blsater ona towel and put it on mating surface of hub and rotor and rotor and wheel so it won't happen again.

Sent from my BlackBerry 9360 using Tapatalk

UPDATE! Turning this into Baby3's build thread. If a mod wants to move it to the "project" section. Be my guest.

Some people don't like tint, some people don't like chrome taillights. I grew up hating the Altezza/clear lens taillight look so we opted for the red tint. It looks awesome IMO. Looks OEM but..... not.

Had my day off and got bored. I had a can of red VHT niteshades so I went to work. Only prep was wipe the suckers down with glass cleaner and BAM!

http://i10.photobucket.com/albums/a1...3/_MG_2460.jpg

http://i10.photobucket.com/albums/a1...3/_MG_2463.jpg

Next is an exhaust. Going to delete the muffler on the Galant and make my own Buddy Club SpecII for it so the MZ3 gets the old can. Only planning to do an axle-back depending on what my exhaust guy can hook me up with.

Nice ass^

Looks 10x better this way. Good job Jigz.

I would have left the backup light clear for more of an OEM look, but it looks sharp regardless. Nice.

Shit, I kinda like it all redded out, looks mean!

Quote:

---

Originally Posted by Skyforger

I would have left the backup light clear for more of an OEM look, but it looks sharp regardless. Nice.

---

This!

Sent from my Nexus S 4G using Tapatalk 2

Looks so oem that I couldn't figure out what you did til i read. I like it though.

All red looks great, wouldn't look as sharp with a clear reverse section.

Sent from my Rooted Droid X using hacked Tapatalk 2