Palmz JDM 8G Galant Pic heavy

Bought this for cheap when i sold the bmw, im in school so progress will be slow for a bit.
The car was sold cheap becoz the manual transmission is faulty ether completely broken or just a simple clutch bearing

Info about the car
Its a 2000 Model
2.0l Manual :D
driven 174 thousand KM


NOTE a bunch of picz in this thread are just to show you whats diffrent with the jdm like pics of fuse boxes and so on.

I think its safe to say that im the only member with bot JDM and USDM galants at the same time so im when im fiddling with the car i can dell what will and wont fit the usdm car

bought it like this didnt start becos the fuel pump wouldn't run then it magically reapers it self
http://i1193.photobucket.com/albums/...4-26152506.jpg
quik wash
http://i1193.photobucket.com/albums/...4-26154853.jpg
I will admit this the only reason i bought the car now is becoz i was given a chance to rip out a leather interior out of a jdm and i just couldn't pass that up but i had nothing to put it in so i bought the car ( it had bin on sale for a couple of months now)

http://i1193.photobucket.com/albums/...4-27162348.jpg
trolly full of interior shit
http://i1193.photobucket.com/albums/...4-27162355.jpg
Im not going to be using all of it since i want to blend more black with the tan interior.

My Baby g and the new one
http://i1193.photobucket.com/albums/...4-27143319.jpg

here is a pic of the old interior
http://i1193.photobucket.com/albums/...4-27152852.jpg

I noticed that if you would buy jdm or eudm interior for a usdm galant you would have to fabricate the bolt on points for the rear seats the front seats would fit tough
also the jdm rear seats tilt forvard like this unlike the usdm wich only tilts one back
http://i1193.photobucket.com/albums/...4-27170849.jpg

arm rest and head rest LUXURY
http://i1193.photobucket.com/albums/...4-27172133.jpg
fronts with center console installed
http://i1193.photobucket.com/albums/...4-27185305.jpg
i could have changed out the stock in between the doors for a tan one but i found this to be a little more stylish
http://i1193.photobucket.com/albums/...4-27211714.jpg

also here is a little known fact.. the tweeters on the mirrors are bigger than the usdm ones also mid range tweeter in stock speakers
http://i1193.photobucket.com/albums/...4-27192421.jpg

little things like this that show the car is built with a bit more attention to detail than the usdm ones plastic cap over the screw in the door holder thingy
http://i1193.photobucket.com/albums/...4-27201918.jpg


now to a thing i find verry annoying about the car if you notice the seats, The center line isnt centered you arent suppose to sit centered in it like the usdm car but im a big man and for me it feels as so the steering wheel is a bit to the right witch annoys the fk out of me i like sitting and driving my usdm car much more... i dont know how to say it but it just fits better..
http://i1193.photobucket.com/albums/...4-27211739.jpg

also the leather door cards are more tight on the usdm galant which i like not flappy like in the jdm.. .... ( I like my door card like I like my women tight)

fuse boxes are different
http://i1193.photobucket.com/albums/...4-27150149.jpg
http://i1193.photobucket.com/albums/...4-27152910.jpg

Engien bay verry welcoming of a vr4 swap ;P
http://i1193.photobucket.com/albums/...4-27150134.jpg


Now to the thing i HATE most about this car.. you cant google shit about it most of the results especially the top ones on google only show USDM cars and when im trying to look for something that is not the same in both car its a bitch and yes i tried to type JDM or eudm stuff like that, and the forum community sucks verry inactive

also the jdm and the eudm galants seem to be more prone to rust than the us spec i noticed this a while ago driving around i would notice the galants and soon be able to recognize from far away if it was jdm or usdm just by the big front bumper on the us spec car. rust on the jdm and eudm cars is always on the fender around the wheel but the usdm cars seem to only have rock chips on the hood there are exceptions of course.
This car is a bit rusty and dinged to make it onehunded i would have to buy me some front fenders front bumper fog lights drivers side door and fix the rear fenders

PLZ READ THIS: i need to know how to open the drivers side door its stuck closed and i really dont want to ruin the inner door panel my guess is that the metal rod that goes to the handles got loose when i was installing the door card or something
any awnsers to this as quik as posible would be nice


I hope you guys enjoy this project as much as i do

For the driver door, the inside handle isn't working at all? Best bet without ruining anything is probably taking the screw out of the inner door handle and seeing where the pull rod is disconnected and try to get it re-attached.


I'm jealous you get to choose from either USDM or JDM! That's awesome.

Haha thank you. But im sure its the mechanism ive alredy taken it out and the motor is stuck
http://img.tapatalk.com/d/14/04/28/requ5a3a.jpg

Sent from my GT-I9505 using Tapatalk

i got the door panel of and was able to remove the locking mechanism then i just disconnected the motor from the rest of the mechanism and now i can close and open the door again

Few more pix and some videos
http://i1193.photobucket.com/albums/...4-28174919.jpg
http://i1193.photobucket.com/albums/...4-28174926.jpg
http://i1193.photobucket.com/albums/...4-28174944.jpg
need the brake light for the spoiler.... not sure about the spoiler tho what do you guys think?

Here is a video of a start up. u can hear the bearing noise in the gearbox and it goes when i push the clutsh at about 24 sec mark
http://i1193.photobucket.com/albums/...4-28174627.jpg

Who would want this? I think ive seen someone put the shifter knob on a usdmhttp://img.tapatalk.com/d/14/04/29/jyme9ehy.jpg
I also have 3 chrome jdm door handels

Sent from my GT-I9505 using Tapatalk

Your video sounds like a throw out bearing like you are thinking.

Also post your items in the for sale section =) We love JDM stuff. I already have chrome handles though.

Yeah I will I just have to get some shiping rates first if anyone could tell me a couple zip codes I could try to gibe you guys an idea of how much the shiping is that would be great

Sent from my GT-I9505 using Tapatalk

Sneak peek at what's to come ; P

http://img.tapatalk.com/d/14/05/04/y8ebebar.jpg
http://img.tapatalk.com/d/14/05/04/e6enutuz.jpg

Sent from my GT-I9505 using Tapatalk

I started the dreadful procedure of getting the bearing out of the transmission

Well this is how it all starts isnt it?

http://i1193.photobucket.com/albums/...5-02134247.jpg

Every little thing was rusted stuck the brake rotor it self took way to long to get of.

shifter cables you can see that the bushing is torn to shits
but at this moment its more important to fix the gearbox and put it back together. worry about the rest later
http://i1193.photobucket.com/albums/...5-02162620.jpg

Hover car

http://i1193.photobucket.com/albums/...5-03102600.jpg

Much better than hover cat :duh:

As suspected input shaft bearing. found allot of little peaces floatin around the trans
http://i1193.photobucket.com/albums/...5-03144018.jpg

http://i1193.photobucket.com/albums/...5-03144616.jpg
But this is the only damage i can see, not really sure tho if its actual damage it looks like it could be factory machined dont know why tho. :087:

Magnet before. (already took 3 metal chards of it)
http://i1193.photobucket.com/albums/...5-03161346.jpg

After :) i know it needs to be wiped off just a little more before assembly
http://i1193.photobucket.com/albums/...5-03162306.jpg

The infamus bearing and some of its components
http://i1193.photobucket.com/albums/...5-03163117.jpg

The loose input shaft did this. its the thing that holds the clutch bearing on the input shaft. (not sure what its called). this will not be replaced im told it doesnt matter all that much.
http://i1193.photobucket.com/albums/...5-03163812.jpg

http://i1193.photobucket.com/albums/...5-03165255.jpg

This guy I fkn hate this guy he was just stuck there not doin shit in the way when taking the gearbox out.. got him at the end 2 crow bars and one screw driver...
http://i1193.photobucket.com/albums/...5-03172810.jpg


Also weve bin wondering what that thing is on the fan bracket? some sort of resistor?
http://i1193.photobucket.com/albums/...5-03173852.jpg

--- Also Please help which gearbox do i have F5M42 or F5M41? (2.0l JDM 2000model Galant) im also unsure if i have a 4g63 or a 4g94? sorry about the noobish questions

got bored so i did this :P
http://i1193.photobucket.com/albums/...5-04144704.jpg
http://i1193.photobucket.com/albums/...5-04145904.jpg
hope i can get the bearing and oil seals tomorow then it should be on the road again Tuesday or Wednesday

i had that same issue with my eclipse trans. as far as not knowing what engine you have, look on the block. there should be a stamp behind the exhaust manifold with the engine code on it. its prob covered in grease or rust, just have a small wire brush, brake clean and a rag handy.

Quote:

---

Originally Posted by pernir

shifter cables you can see that the bushing is torn to shits
but at this moment its more important to fix the gearbox and put it back together. worry about the rest later
http://i1193.photobucket.com/albums/...5-02162620.jpg

---

Here in 'Merica we can get metal bushings to replace the rubber ones. One place is called SpeedSource and the other is in Canada, TWM Performance. I have no idea if the USDM and yours has the same shifter cables, looks like the same setup.

Quote:

---

Originally Posted by kylecanthurdle

i had that same issue with my eclipse trans. as far as not knowing what engine you have, look on the block. there should be a stamp behind the exhaust manifold with the engine code on it. its prob covered in grease or rust, just have a small wire brush, brake clean and a rag handy.

---

Yeah i heard this is a common bearing to go in mmc trans, and ill look on behind the exhaust see if i cant find it :)

Quote:

---

Originally Posted by Black8GV6

Here in 'Merica we can get metal bushings to replace the rubber ones. One place is called SpeedSource and the other is in Canada, TWM Performance. I have no idea if the USDM and yours has the same shifter cables, looks like the same setup.

---

Is there any reasion i should look for metal ones instead of rubber ones? dont they just make more noise and rust?. Maybe faster shifting?

Quote:

---

Originally Posted by pernir

Is there any reasion i should look for metal ones instead of rubber ones? dont they just make more noise and rust?. Maybe faster shifting?

---

They won't break like the rubber ones and they make shifting direct, it takes the slack out of shifting. Also metal shifter base bushings would be good to add too, same reason.

The cable bushings are brass, I sprayed mine with some WD-40 rust prevention over a year ago and they still look brand new.

Quote:

---

Originally Posted by Black8GV6

They won't break like the rubber ones and they make shifting direct, it takes the slack out of shifting. Also metal shifter base bushings would be good to add too, same reason.

The cable bushings are brass, I sprayed mine with some WD-40 rust prevention over a year ago and they still look brand new.

---

Thanks ill keep that in mind. when i go looking for the bushings :)

UPDATE geabox is on the car and the car is running perfect need to attend to some little things in the future like cv axle boot wheel bearing and ball joint nothing major the bearing is the only thing that i feel i could just see that the other stuff needed changeing befor it went bad


stupid thing is faster than my usdm.. fkn autoz

Nice! bet it felt good

Quote:

---

Originally Posted by Black8GV6

Nice! bet it felt good

---

Oh u wouldn't believe. Ive never even done a clutch swap before so taking a whole gearbox apart and putting it together CORRECTLY was very stressful. First time for everything huh?

What is this noise it sound like some sort of fabric rubbing together it sort of comes from the steering column . annoying the fk out of me
i was thinking maybe a bearing but bearings dont sound like this

http://i1193.photobucket.com/albums/...5-07214658.jpg

i want that cluster lol, but really, good job on taking the tranny apart and fixing it!