Trouble with ecuflash need som help

im trying to disable the immob on my evo 8 ecu. so to do that im getting peripherys to show so im modifing the evo7base.xml file with the following lines just before the <rom/> and for some reason im not getting them to show no matter what i try anyone know what is up? do i need an older copy of ecu flash or should i not being trying this on a vista laptop? somethings gotta be messing with it and here the lines and im using ecu flash ver. 1.42.2595


<scaling name="blobbits" storagetype="bloblist" storagebits="1">
<data name="0" value="00"/>
<data name="1" value="01"/>
</scaling>

<table name="ECU Periphery00 (F9A) Bits" category="ECUPeriphery" address="f9a" type="2D" level="2" scaling="blobbits">
<table name="Periphery Bit Number" type="Static Y Axis" flipy="true" elements="16">
<data>bit.15</data>
<data>bit.14</data>
<data>bit.13</data>
<data>bit.12</data>
<data>bit.11</data>
<data>bit.10</data>
<data>bit.9</data>
<data>bit.8</data>
<data>bit.7</data>
<data>bit.6</data>
<data>bit.5</data>
<data>bit.4</data>
<data>bit.3</data>
<data>bit.2</data>
<data>bit.1</data>
<data>bit.0</data>
</table>
</table>

<table name="ECU Periphery0 (FAA) Bits" category="ECUPeriphery" address="faa" type="2D" level="2" scaling="blobbits">
<table name="Periphery Bit Number" type="Static Y Axis" flipy="true" elements="16">
<data>bit.15</data>
<data>front o2 sensor heater circuit </data>
<data>bit.13</data>
<data>bit.12</data>
<data>Disable EGR / Enabled Ign Adv (set bit=1)</data>
<data>timing knockdown on light acceleration and less than 3000rpm</data>
<data>Enable Warmup Ign Retard</data>
<data>bit.8</data>
<data>Enable High Oct Ign Map Lookup (and many other subroutines)</data>
<data>"WG solenoid? Enable Speed Limit Test"</data>
<data>bit.5</data>
<data>for full time open loop set to 0</data>
<data>Immobilizer (1=enable 0=disable)</data>
<data>bit.2</data>
<data>rear o2</data>
<data>bit.0</data>
</table>
</table>

<table name="ECU Periphery1 (FBA) Bits" category="ECUPeriphery" address="fba" type="2D" level="2" scaling="blobbits">
<table name="Periphery Bit Number" type="Static Y Axis" flipy="true" elements="16">
<data>bit.15</data>
<data>bit.14</data>
<data>bit.13</data>
<data>bit.12</data>
<data>bit.11</data>
<data>bit.10</data>
<data>bit.9</data>
<data>bit.8</data>
<data>bit.7</data>
<data>bit.6</data>
<data>2nd thermo fan table</data>
<data>bit.4</data>
<data>bit.3</data>
<data>bit.2</data>
<data>bit.1</data>
<data>Lean Spool</data>
</table>
</table>

<table name="ECU Periphery2 (FCA) Bits" category="ECUPeriphery" address="fca" type="2D" level="2" scaling="blobbits">
<table name="Periphery Bit Number" type="Static Y Axis" flipy="true" elements="16">
<data>P0443, P0446, P0403, P0243, P0090, P2263</data>
<data>P0450, P0451, P0452, P0453 Evap</data>
<data>P0441, P0442 Evap</data>
<data>bit.12</data>
<data>P0031, P0032, P0037, P0038</data>
<data>P1400 MAP Sensor</data>
<data>P0401 EGR Test</data>
<data>P0506, P0507 Idle Test</data>
<data>P0170 (P0171, P0172)</data>
<data>P0134 Front O2</data>
<data>P0300; set bit.4 and bit.5 to 0 to disable</data>
<data>P0300; set bit.4 and bit.5 to 0 to disable</data>
<data>P0132, P0136 O2</data>
<data>P0133, P0159</data>
<data>P0421 not in FSM</data>
<data>bit.0</data>
</table>
</table>

<table name="ECU Periphery3 (FDA) Bits" category="ECUPeriphery" address="fda" type="2D" level="2" scaling="blobbits">
<table name="Periphery Bit Number" type="Static Y Axis" flipy="true" elements="16">
<data>P0128 CT Below Reg</data>
<data>P1603 Battery Backup</data>
<data>bit.13</data>
<data>bit.12</data>
<data>P0180 - P0183, P0461, P2066 Fuel Sensors</data>
<data>bit.10</data>
<data>bit.9</data>
<data>bit.8</data>
<data>P0551 PS Pressure</data>
<data>P0500 Speed Sens</data>
<data>bit.5</data>
<data>bit.4</data>
<data>bit.3</data>
<data>P0234, P0243, P2263</data>
<data>P0510 not in FSM</data>
<data>P1715, P1750, etc</data>
</table>
</table>

<table name="ECU Periphery4 (FEA) Bits" category="ECUPeriphery" address="fea" type="2D" level="2" scaling="blobbits">
<table name="Periphery Bit Number" type="Static Y Axis" flipy="true" elements="16">
<data>P0140 Rear O2 No Act</data>
<data>P0069 MAP vs Baro</data>
<data>P0111 IAT Circuit</data>
<data>P0554 PS Press Sens</data>
<data>P1530 A/C1 Switch</data>
<data>bit.10</data>
<data>bit.9</data>
<data>P0830 Clutch Pedal Circuit</data>
<data>P0090 Fuel Pressure Circuit</data>
<data>bit.6</data>
<data>bit.5</data>
<data>bit.4</data>
<data>bit.3</data>
<data>bit.2</data>
<data>bit.1</data>
<data>bit.0</data>
</table>
</table>

*edit* and yes the tables and all the scaling and such are spaced accordingly even if it doesnt show it here

alright fixed it had to moving scaling values out so it would show i figured the scripting was off.

hey, what did you do excactly, because I have the ecu peripherys showing in ecu flash, because that what I see, I don't see any options to edit the individual bits in FAA section, where the imob is at.
http://i739.photobucket.com/albums/x...man45/imob.jpg

here you go bro.
- <table name="ECU Periphery0 Hex (FAA)" category="Periphery" address="FAA" type="2D" level="4" scaling="Hex16">
- <table name="Selector" type="Static Y Axis" elements="8">
<data>+0</data>
<data>+1</data>
<data>+2</data>
<data>+3</data>
<data>+4</data>
<data>+5</data>
<data>+6</data>
<data>+7</data>
</table>
</table>

put 0x52d6 in all 8 table
also put in the imm 52d6

Tried that, didn't work I even tried something else the evom guys suggested. nothing, I'm about ready to go fricken take a sledge to this ecu... I'm so pissed

How about a Evo VIII ROM file already setup with the immobilizer disabled?


http://www.club3g.com/forum/3g-eclip...load-here.html

^I've tried one from a member here but Ill give anything a shot lol

maybe I'm having a brain fart and over looked something. The g will start with evo 8 timing right? the timing isn't that far off compared from SOHC to DOHC?

Should fire right up. I have used the above link ROM flash on a customer's Eclipse with the Evo ECU installed with no issues.

yes you should increase the timing a little since the g64 have a bigger deck. I'm going to try the evo timing on my stock PCM since i made a lot of progress finding the maps. I'm waiting for mysticj for the jdm g63 maps. Stock PCM is perfect for N/A tuning even 5 speed swap tuning. I found the knock maps on the stock pcm and with the help of SPD_FRK we could use a knock sensor with the stock G pcm.YEAH YEAH knock sensor dont come with the G64. Wrong!!!! Is the harness on our g that do not have the knock sensor wire but it turns out the pcm have the maps and the pin for the knock sensor is there.

Quote:

---

Originally Posted by SPD_FRK

Should fire right up. I have used the above link ROM flash on a customer's Eclipse with the Evo ECU installed with no issues.

---

Tried that rom, still no start. I even had a buddy of mine whos good with computer programing come out, and he got the tables to show up in ecu flash that I needed to have so I could BIT enable or disable the imob, so I put a 0 in for the imob, for ecu periphery, and FFFF in hex, still all the car does is crank. doesn't start. But I put the stock ecu in, fires right up. Now my question is, is the ecu came with a tephra mod on it, I didn't download it from it, I just installed new rom with the same ID. Could it be that even ecu flash says its getting the imob off, could the immob still be locked? What about getting the stock rom off my evo ecu, is that possible to bring that back? And you make harnesses, so as far as I know the pinouts dont change for the 02 03 model for the ecu pinouts right? or DO they? if they do change, then I probably have a wrong pinout... any help would be awesome.

message me your email, ill send you my rom it works for mine and you can compare to see if you can get it to work

^ok pm sent, thanks man