man I dont remember my exact dmensions. I will try to figure it out......
i need pictures of intercoolers on the galant preferably with the dimensions
Brandon - 2001 Galant GST 5speed
Wiseco // Eagle // PTE // Holset // Turbonetics // Supertech // Blox // Prosport // Vibrant // Innovate // OpenEcu // Mishimoto // Magnaflow // Walbro // XXR // Rotora // Brembo // Hawk // R1 Concepts // Dc Sports
man I dont remember my exact dmensions. I will try to figure it out......
99' Galant ESOriginally Posted by qnz
4G64/63T
AEM EMS
X2 I need this info too. I know Stewi you told me not to get 3" piping if i did not want to trim the bumper.
whatever you do, don't get one as big as TJ had. Shit didn't fit right and made the bumper all warped because it was so big.
28" long x 6" tall x 3 1/2
On Stock Bumper:
00 Galant ES Turbo/5-Speed
13 GTR
^God I miss looking @ pics of your car....
OZ Rally Crew #001, Quaife Club member :D
thanks ICed. For now i will turbo the stock motor when i finish my 5 speed swap. I have a spare head i'm going to take it to the machine shop to get it clean and change the head gasket and engine bearings before turbo. MY evo 2.5L swap is on hold for a little until i get some money so i could take the block and head to the machine shop also i need forge piston -_-.
Lancer/EvolutionX Rotor Glow Paint
6g74 Forged Engine w/ hx40 turbo
Eclipse GT 5 spd swapped
Rotor Glow Galant
Daily Galant
OZ Edition Eclipse
No Prob, Thats with the stock crash bar in-tact also if that makes an difference.
She looks the same, Just real dusty haha.
00 Galant ES Turbo/5-Speed
13 GTR
99' Galant ESOriginally Posted by qnz
4G64/63T
AEM EMS
Do you even drive her anymore Ron?
OZ Rally Crew #001, Quaife Club member :D
Here is my older intercooler... core size 22x10x3, overall length 30" 2.5"inlet/outlet
Its mounted below the stock crash bar, bumper is significantly cut to fit.
same intercooler test fitting my old style jdm front. see how warped the bottom of the bumper is, thats because its hitting the intercooler...
same intercooler, painted black, just to show how it was mounted....
this pic is getting ready to install the larger intercooler. If you look at the vertical support under the hood latch, the bottom where the power steering cooler pipe bolts thru it, I cut that area out/flat, this gave me an additional 5/16" worth of clearance. I just welded the vertical support to the top of the lower radiator support.
this is the new one ready to go in. I dont have the exact specs but I think these measurements are close...core 26x12x3, overall 32" 3" inlet/outlet
close up of the cut spot...
intercooler recessed into the crash bar....
mounts to the back of the bar....
hole big enough to get a socket thru the crash bar to tighten the bolt/nut
with it all installed, there is slightly over 1/8" between the rad support and back of the intercooler.... in the pic its about 3/8" but thats because I didnt yet grind down the welds I did so it was hitting the weld. Right this moment its about 1/8" away....
Last edited by Stewi; 07-27-2011 at 03:43 PM
99' Galant ESOriginally Posted by qnz
4G64/63T
AEM EMS
I found a few more....
after the bumper was cut.... I probably took about 3/4" off the back of the bumper. I also had to cut half moon shapes on the lower corners to clear the intercooler pipes...
99' Galant ESOriginally Posted by qnz
4G64/63T
AEM EMS
IDK if 7g's count or not
12x27x3 You guys have more room mine is actually hitting my headlights, my crash bar is my intercooler.
1996 galant s
finishing up my 2.4L DOHC, 10.5:1, precision sc60, meth injected MONSTER.
Brian, I had to double check yeah its 3.5" I will re-measure when i get home, but heres from my older post:
https://www.thegalantcenter.org/show...ht=intercooler
No, just sits in the garage. Kind of a shame, hopefully I get the urge lol.
00 Galant ES Turbo/5-Speed
13 GTR
Yeah man for sure double check that. Im hoping it is 3.5" because then im gonna ask you to take a bunch of pics so I can figure out WTF you did to make it fit. For me to go 3.5" I'd have to cut another half inch from the bumper or cut/custom fabricate a lower radiator support.
99' Galant ESOriginally Posted by qnz
4G64/63T
AEM EMS
3.3-.4ish? Or am i just an idiot measuring?
00 Galant ES Turbo/5-Speed
13 GTR
Its probably a 3" core and the end tank is slightly larger. Mine is kinda like that too. My end tank is lik3 3.125" but my core is 3".
99' Galant ESOriginally Posted by qnz
4G64/63T
AEM EMS
Thats interesting though, I didnt think the new style front had more space than the old style. I think if I ever try to go to a 4" I will need a dolphin front.
99' Galant ESOriginally Posted by qnz
4G64/63T
AEM EMS
Bookmarks