So they are trash?
Sent from my Z796C using Tapatalk
I'm honestly surprised whomever has put miles on those things isn't dead. Holy fuck.
So they are trash?
Sent from my Z796C using Tapatalk
Currently on my 3rd 8G... Not giving up this time!
Take the mounts off and find out.
'99 5-Speed GTZ: Forged 3.6L 6G74T 6764 E85
2017: 552whp/562wtq SBE on 19psi'02 Eclipse GT: 6G72 M/T-swapped Daily Driver'10 Endeavor: 6G75 AWD Family-mobile
I will. Couldn't get to it today.
Sent from my Z796C using Tapatalk
Currently on my 3rd 8G... Not giving up this time!
I'd get rid of that setup all together. They're as bad as cut springs. Find something stock you can run temporarily.
Well that's no good. FML!!! Nobody in my area is selling anything either.
Sent from my Z796C using Tapatalk
Currently on my 3rd 8G... Not giving up this time!
My stock suspension is coming off within the next month. You can have it for free to get u by. Throw me a couple of bucks and shipping and it's yours if u r willing to wait for a bit.
Sent from my Galaxy S4
'00 Mitsubishi Galant ES 4g64T (Samantha)
'01 Mitsubishi Galant ES 4g64 (Daily)
'02 Mitsubishi Galant ES 4g64 (SCRAPPED)
'00 Mitsubishi Galant ES 4g64 (SCRAPPED)
'91 Volvo 740 Turbo B230FT (SOLD)
'88 Mitsubishi Mighty Max (SOLD)
'91 Kawasaki ZX7 (SOLD)
'95 Kawasaki ZX9R
BlackDragon, don't take all the negative comments about those specific sleeves to mean that all sleeves are bad.
The ones on your dampers are just junk. If I were you I'd stay on your blown stock stuff (as anything you buy used will likely also be blown or near it) and just save up for something that will actually last. Why work/spend twice?
Thanks Blue8g. I just wish I didn't spend the $100 on that set up.
Sent from my Z796C using Tapatalk
Currently on my 3rd 8G... Not giving up this time!
And SPD race... I'd be down but I think I need it asap
Sent from my Z796C using Tapatalk
Currently on my 3rd 8G... Not giving up this time!
When my rear gr2s blew, the struts had oil on em, that had a distinct smell..almost like baby oil but a lil more solvent like. I'm now on gr2s in the front and agx in the rear. The fronts managed to survive, so I never switched to agx. I'm on springs btw. Besides the rears blowing I don't really have anything bad to say about kyb..I mean I could only expect so much from an oem replacement. Now if I had the agxs to begin with, and they blew as fast, I woulda been upset. Because when I had agxs all arojnd on my 240sx, they lasted over 3yrs until I totaled it. Also ran springs on that car. Rockauto has good prices if you need kybs..also google rock auto discount code. Usually 10% off ones floating around
Thank you 8thLS6.
Sent from my Z796C using Tapatalk
Currently on my 3rd 8G... Not giving up this time!
Oh, and I just bought driver inner tie rod and passenger outer tie rod, new flex pipe that has to be welded in, and a cat back! Can't wait to tear into it and get it legal.
Sent from my Z796C using Tapatalk
Currently on my 3rd 8G... Not giving up this time!
So, I have a question. I went to replace the driver inner tie rod and couldn't get it out for anything. Went to Autozone and rented their inner tie rod tool to find out it was too big and just spun. Any advice on getting the old one out so I don't have to pay $200 to a shop to do it?
Sent from my Z796C using Tapatalk
Currently on my 3rd 8G... Not giving up this time!
15 F150 3.5 ecoboost 4x4 - daily driver
01 Galant ES V6 MT (sold)
00 Eclipse RS MT
^aww yeah! workin in snow and not givin a crap! thats what its all about right there
The "Tumbler" Is HereStock Longblock/Stock PCM | Custom Garrett 50-1 | 17 Psi | Weighing 2xxxLbs3xxWHP/3xxWTQ [Current]
I wish I was snow. Sheet of ice and then sleet on top of it. All the white is loose sleet. Now I have snow on top of all of it. Lol
Sent from my Z796C using Tapatalk
Currently on my 3rd 8G... Not giving up this time!
Bookmarks