What type of alarm are you installing and what fuses did you blow?
:oops: Hi there, Last night I tried to reprogram my remotes. I started with a wrong connection and saw a spark when I ground it, then the alarm system stopped working. I checked all the fuses and nothing wrong. So, I disconnect the battery and hook it on again. It turned back on again. So, I continued to program it. In the middle of programing, something happend. The negative pole of the battery became disconnected because I didn't fasten it and end up the memory for my remote is gone. And when I shut the door the alarm armed by it self and I cannot get it to unarmed. And my central power luck is not working anymore. I may have put one fuse back in a wrong place? :oops:
What type of alarm are you installing and what fuses did you blow?
Here's the thread on programming the keyless entry. I haven't tried this but good luck with it. http://www.clubtgc.org/forum/viewtopic.php...t=keyless+entry
[size=10]<span style='color:white'>. . . .</span>
I brew the central lock fuse 15A.
Did you get everything fixed or do you still need some help? At my job, I have full access to the Mitchel books, I can give you a complete run down of the electrical system. Just post up and I will contact you.
I replace the blown fuse and the remote came back normal again!! Now I can use my original remote again but still cannot get my second remote to work. But I think that's already much better than the way it was when I couldn't even drive is, isn't it?
Ummm, I would have to say yea. If you still need help with programming the second transmitter, post up Mon. morning and I will check the Mitchell book to see about programming steps. If I have to I can call my connect at Mitsu to see about faxing you something. Just let me know.
That would be great. I tried the method that other member provided but it didn't work for mine or I have done something wrong. My remote only has two buttons(luckunluck). If you figured out how, please let me know.
![]()
No prob, will check it out Mon. Just give me year and trim level and a way to contact you if I have to fax something.
I only know my car is a 99' MITSUBISHI GALANT ES V6 3.0. (what is trim level?). You can ether send it to my e-mail([email protected]) or you can fax it to me (972-416-8844). Thanks.
[/img]
You got it, the trim level is ES, LS or GTZ. I will look it up and have the info faxed or e-mail. It all depends on how I get the info.
I have the pdf of the info that you need thanks to one of the members I downloaded the service manual for our cars. I will try and e-mail you the one section but it is over 3megs. If your hotmail doesn't take it, I will e-mail to myself at work and print it out then fax.
:? I am afraid that hotmail wont hold that much, but I have other two email account to try if you don't mind.([email protected] ; [email protected]) If they don't work, I will keep my fax in fax mode all day. Thanks again.![]()
Will def. try again when I get home to the yahoo add.
Make sure that you can still receive faxes, I just sent it. Let me know if you got it.
Can you send it again please? I thought I set my machine to receive fax only, but I didn't see any printout in my fax machine!? My number is 972-416-8844. Thanks.
Will do first thing in the morning. Should be around 9:30 eastern time.
If you don't mind, can you FAX it to 214-902 2475 during 5:00 PM ~10:00PM central time? That's my work's FAX number. They got better fax machine and I will be there from 5:00pm to 10:00 pm. By the way, I am in Texas. You?
I will get this faxed to you a little after 7pm eastern time. If I can't get it to go. I will take the paper home tomorrow and scan them then e-mail to you.
I got them. They looked perfect. Thank you so much. I will try it again this weekend. I'll tell you the result.
![]()
Bookmarks