Galantman03's 8G Build

**Galantman03** · 11-04-2012, 05:46 PM

And a bump... Ordered some things, most important ones were the clutch and aluminum plate to have the catch can fabbed up. So just a picture.

**finald8ta** · 11-04-2012, 07:48 PM

i want your garage. that is all

**wetamup2k3g** · 11-04-2012, 08:11 PM

It's sitting there like a bully in detention, with this look on his face like,"wait till I get outta here, I'm about to kick somebody's ass!!! Shit is on when I get out!!!" Keep the pics coming Jared!

**M-Rod** · 11-04-2012, 08:16 PM

Looking good! One step closer.

**Galantman03** · 11-05-2012, 06:57 PM

Originally Posted by finald8ta

i want your garage. that is all

Idk man its kinda bare lol

Originally Posted by wetamup2k3g

It's sitting there like a bully in detention, with this look on his face like,"wait till I get outta here, I'm about to kick somebody's ass!!! Shit is on when I get out!!!" Keep the pics coming Jared!

i cant wait for the intercooler.... Its gonna be mean!

Originally Posted by M-Rod

Looking good! One step closer.

Yeah, maybe 2 steps back.... HPF doesn't have the clutch in stock.... Grrr....

**Ivory8g** · 11-05-2012, 07:04 PM

Jared what clutch? I probably have it here and can ship it right out.

**Galantman03** · 11-05-2012, 07:24 PM

Competition clutch twin disk evo 9 tranny (if it matters), rated tq 750

**M-Rod** · 11-05-2012, 08:39 PM

MAP usually has the Exedy twin disc. Any specific reason you didn't go that route?

**Galantman03** · 11-05-2012, 08:48 PM

Dont want a pull clutch, and exedy is kinda expensive for how long they last imo

**8thLS6** · 11-05-2012, 11:49 PM

Man that's a nice work space

**6G72gearhead** · 11-06-2012, 12:40 AM

How are you routing your crank case vent?

Actually more specifically where after the catch can?

**Silvertune** · 11-06-2012, 06:51 AM

Competition makes good clutches.

**Galantman03** · 11-06-2012, 08:01 AM

Originally Posted by 6G72gearhead

How are you routing your crank case vent?

Actually more specifically where after the catch can?

Down away from the cover using -10 an connectors. And vta catch can.

**Ivory8g** · 11-06-2012, 01:22 PM

pm sent :)

**6G72gearhead** · 11-06-2012, 04:52 PM

Is South Dakota an emissions state? I have seen a lot of good luck by routing the lee side of the catch can to a port in the exhaust stream. It helps pull a slight vacuum on the crank case while eliminating the smell associated with an open vent. The problem with routing to the intake is that oil mist lowers knock resistance.

**Galantman03** · 11-06-2012, 05:55 PM

No, we arent an emissions state. I'm not worried about the suck factor lol. The tank is low, so once vapors enter the line and start to condense, gravity takes, and should flow nice into the tank. I'm not going to have any vapors enter the intake track or the exhuast.

Went from this ugly set up

To this

And welded up the steel -16 an to the water pipe.

**Galantman03** · 11-12-2012, 06:38 PM

Well no luck on the clutch gotta wait. But time for wire tuck time

**wetamup2k3g** · 11-12-2012, 06:56 PM

This is how clean your engine bay is.....just now I said to my (desperately non-mechanically-inclined) wife, "look how clean this engine bay is?" and she looked, squinted and said "wow, it's like no wires at all, how'd he do that?" Normally, she has no clue what mods might be where on a car, so if she can look and see how clean that ish is, that's saying something!