Post a pic as your car sits now....

[Joshua42007]

It would of been 100% perfect if the headlights weren't condensated....

Lol very good observation. i didn't even notice it until you mentioned it.

[2kgalant]

Honestly guys, I don't know why it condensated all of a sudden. The previous day, I didn't even wash car, so I don't know how water got in there. All I know is that day of the show, it drizzled off and on and it was very hot and humid. The condensation has gone away.

[Joshua42007]

Honestly guys, I don't know why it condensated all of a sudden. The previous day, I didn't even wash car, so I don't know how water got in there. All I know is that day of the show, it drizzled off and on and it was very hot and humid. The condensation has gone away.

Your car still looks amazing, the condensation will go away after awhile. Yeah i really hate it when that happens, about 3 weeks ago i got my new projector headlights in the mail, by the next day they were fogged up. I wish i knew how to get rid of the problem.

[Serstylz2]

when my Projectors get foggy i just turn on the beam and it clears up

[spardavr4]

Just got my Greddy SP2 installed. Sounds awesome except the friggen piping from the V6 Eclipse didn't work at all. The tubing didn't go over the crossmember and instead went underneath so I had to get that customized. I thought that you only needed to extend it by 10" but even the mounting brackets didn't line up correctly.

[greddy]

Just run it under the cross member... that's how all the greddy exhausts are.supposed to go

[Reelax]

Just run it under the cross member... that's how all the greddy exhausts are.supposed to go

yeah, but that's too low if you are lowered more than 2". i specifically had them run over the cross member on my custom piping because i knew i was gonna be down past 2.5" in th rear.

[02redgalant]

Your car still looks amazing, the condensation will go away after awhile. Yeah i really hate it when that happens, about 3 weeks ago i got my new projector headlights in the mail, by the next day they were fogged up. I wish i knew how to get rid of the problem.

some retrofitters use silicon packets in there headlights ..i included...you can buy them from retrofit source...or even your local shoe store there inside shoe boxes

[spardavr4]

yeah, but that's too low if you are lowered more than 2". i specifically had them run over the cross member on my custom piping because i knew i was gonna be down past 2.5" in th rear.

That's exactly what I was afraid of. I wanted it to go under the crossmember but I was too afraid of anything hitting the pipes. Sounds good though. Thank you Greddy for showing my brother that video of your exhaust. However it's not like I was planning on lowering my car. I should have run it underneath, but oh well. What's done is done.

[zobgel]

from my camera phone

[dGALANTc]

^^^^BEAUTIFUL!!! love the mirrors the most. are they m3's modified to look so hawt!?

[4g63lover]

[03GalantEs]

how many inches are those rims? and how much did you lower ur galant?

[4g63lover]

how many inches are those rims? and how much did you lower ur galant?

Are you asking me or are you asking zobgel?

Mine is 16x6 with 225/50/16's. I'm dropped almost all the way in the front and about a 1/4" left on the perch in the rear on Tein SS-P.

[OMEGA PHX]

Almost there just need to trim the shrouds and install the ccfl halos, Also I need to wait a week for the paint to fully cure before installing the lense:


Testing the halo's:

[johnygezony]

Nice !

[showtime]

look amazing, I cant wait to start my project.

[02redgalant]

good work omega..welcome to the club

[Stewi]

Looks good. A little advice on trimming the shrouds, keeping making small straight/even cuts using a dremel with a cutoff wheel, and test fit between each cut. Its really easy to take off too much material. Also cut on a fairly low speed because if the wheel jumps it can hit the shroud and mess up the chrome.

[OMEGA PHX]

Thanks for the compliments guys, this is the first like true mod I have done myself, This is my first time using a dremel and everything.

Looks good. A little advice on trimming the shrouds, keeping making small straight/even cuts using a dremel with a cutoff wheel, and test fit between each cut. Its really easy to take off too much material. Also cut on a fairly low speed because if the wheel jumps it can hit the shroud and mess up the chrome.

Thanks for the advice, I'm actually using a grinding stone bit to trim it, I don't have any cutoff wheels, Yeah already the dremel jump and messed up a little chrome but it was on a part that had to be trimmed so nothing too serious.